![Arderia СP3 20/6B 130 — обзор циркуляционного насоса: установка и обслуживание [6/6]](/img/pdf.png)
Arderia СP3 20/6B 130 — обзор циркуляционного насоса: установка и обслуживание [6/6]
![Arderia СP3 15/4B 130 Инструкция по эксплуатации онлайн [6/6] 613054](/views2/1809390/page6/bg6.png)
4. Delivery set
Circulating pump - 1 pc.
Fitting with nut - 2 sets.
Instruction Manual - 1 pc.
Packaging - 1 pc.
5. Design and operation principle
The pump is equipped with the motor that has a “wet rotor” , isolated from the stator by sealed
sleeve. The pump uses shaft and radial bearings made of ceramic, axial bearing made of
graphite. Bearings are lubricated with the pumped liquid. The protective sleeve of the rotor and
the bearing plate is made of stainless steel, impeller is made of technical polymer, the pump body
made of brass.
Three-way switch changes the motor speed and optimizes the intensity of the circulation of the
coolant in the system.
The pump is equipped with thermal protection, to prevent possible overheating of the pump as a
result of blocking of the impeller.
6. Installation, putting into operation and maintenance
Installation of the pump, putting into operation, maintenance and repair should be carried out by
authorized organization (professional). Execution of works should be formalized by special
document.
Installation of the pump should be made after installation and cleaning of the heating system. The
pump has a threaded flange for connection to the system. Connection should be made with the
help of fittings with cap nuts and washers, supplied with
The arrow on the pump housing indicates the direction of movement of coolant. The pump shaft
must be located in a horizontal plane. Connection of the pump has to be made through residual
current device with the current response that does not exceed 30 mA. To ensure all-pole
disconnection from the mains connection of the pump should be carried out through a two-pole
switch with a contact separation of at least 3mm in all poles, connected directly to the power
terminals and mounted in the fixed wiring.
Before starting the pump operation it is necessary to fill the system with coolant and remove air
from it. To achieve the required speed, use the three-way switch of pump speed.
7. Troubleshooting
Table 2
Design of the products or delivery set may be amended and not indicated in this instruction
manual. However these changes do not impair the quality of the product.
Malfunction Reason Troubleshooting
The pump is not working There is no power Check the power supply
The pump is not pumping water
or a very small stream of water
Lock of the pump bearings
Contamination of the pump
Remove the pressure in the system.
Loosen the screw on the front side of the
stator. Turn the shaft with a screwdriver.
There is no coolant in the heating
system
Fill the heating system with coolant. Open
valves
The pump makes noise The air in the pump Remove air from system
Low voltage of power supply Set the voltage stabilizer
6
Содержание
- Руководство по эксплуатации p.1
- Руководство по эксплуатации p.3
- Технические характеристики давление в системе не более 1 0 мпа 10 бар p.3
- Таблица 1 p.3
- Назначение изделия электронасос циркуляционный предназначен для обеспечения принудительной циркуляции теплоносителя в системах отопления закрытого типа также насос может применяться в системах горячего водоснабжения охлаждения и кондиционирования воздуха в качестве теплоносителя могут применяться вода для систем отопления соответствующая vdi 2035 или водно гликолевая смесь соответствующая astm d3306 изделие сертифицировано информация о дате изготовления приведена на идентификационной табличке p.3
- Меры безопасности данное руководство содержит принципиальные указания которые должны выполняться при монтаже эксплуатации и техническом обслуживании изделия в целях избежания несчастных случаев и исключения поломок необходимо внимательно ознакомиться с данным руководством и соблюдать его требования подключение электронасоса циркуляционного далее насоса должно быть выполнено через устройство защитного отключения с током срабатывания не более 30ма запрещается эксплуатация насоса без заземления запрещается перекачивать насосом воспламеняющиеся и взрывоопасные жидкости запрещается использовать насос не по назначению не допускайте работу насоса без теплоносителя или с загрязненным теплоносителем не допускайте замерзание теплоносителя в насосе прибор не предназначен для использования лицами включая детей с пониженными физичес кими психическими или умственными способностями или при отсутствии у них опыта или знаний если они не находятся под контролем или не проинструктированы об использовании p.3
- Technical characteristics pressure in the system no more than 1 mpa 10 bar p.5
- Table 1 p.5
- Security measures this manual provides principal guidance to be followed during installation operation and maintenance in order to avoid accidents and breakdowns you have to read this manual carefully and follow its requirements connection of circulation pumps hereinafter the pump has to be made through the residual current device with the current response that does not exceed 30 ma it is prohibited to use the pump without grounding it is prohibited to pump through the circulation pump flammable and explosive liquids do not use the pump inappropriately do not allow pump operation without coolant or contaminated coolant do not allow freezing of the coolant in the pump the pump is not intended for use by persons including children who have physical sensory or mental disabilities lack of experience and knowledge with the exception of cases when they are supervised or be instructed by a person responsible for their safety children s access to this equipment is prohibited the manufacturer i p.5
- Product purpose circulation pump is designed to provide forced circulation of coolant in the heating systems of closed type also the pump can be used in hot water systems cooling and air conditioning as the coolant can be used water for heating systems which is corresponding to vdi 2035 or water glycol mixture which is corresponding to astm d3306 the product is certified p.5
- Pressure spending characteristics of the pumps are for conditions pumping medium water power supply 230v 2 orifice tap and water shut off fittings correspond to the size of connecting elements of the product p.5
- Instruction manual p.5
Похожие устройства
-
Arderia СPE 25/6AИнструкция по эксплуатации -
Arderia СPE 25/5AИнструкция по эксплуатации
-
Arderia СPE 25/4AИнструкция по эксплуатации
-
Arderia BP 15/12Инструкция по эксплуатации -
Arderia BP 15/9Инструкция по эксплуатации
-
Arderia CP3 32/8Инструкция по эксплуатации -
Arderia CP3 32/4Инструкция по эксплуатации
-
Arderia CP3 32/6Инструкция по эксплуатации
-
Arderia CP3 25/8Инструкция по эксплуатации -
Arderia CP3 25/4Инструкция по эксплуатации
-
Arderia CP3 25/6Инструкция по эксплуатации
-
Arderia СP 50/20FИнструкция по эксплуатации
Узнайте о циркуляционном насосе, его конструкции, принципе работы и правилах установки. Получите советы по обслуживанию и устранению неполадок.