![Haier 1U35MADFRA Инструкция по монтажу онлайн [6/28] 614578](/img/pdf.png)
Haier 1U35MADFRA Инструкция по монтажу онлайн [6/28] 614578
![Haier 1U26MADFRA Инструкция по монтажу онлайн [6/28] 614577](/views2/1812509/page6/bg6.png)
1. Procedures: operation shall be made as per controlled procedures to minimize the probability of risks.
2. Area: area shall be divided and isolated appropriately, and operation in an enclosed space shall be avoided.
Before the refrigeration system is started or before hot working, ventilation or opening of the area shall be
guaranteed.
3. Site inspection: the refrigerant shall be checked.
4. Fire control: the fire extinguisher shall be placed nearby, and fire source or high temperature is not allowed;
the sign of “No smoking” shall be arranged.
1. Indoor unit: nitrogen is sealed during the delivery of indoor units (inside the evaporator), and the red sign at
the top of the green plastic seal cap on the evaporator air pipes of the indoor unit shall be checked first after
unpacking. In case the sign is raised, the nitrogen sealed still exists. Afterwards, the black plastic seal cap at the
joint of evaporator liquid pipes of the indoor unit shall be pressed, to check whether nitrogen still exists. In case
no nitrogen is sprayed out, the indoor unit is subject to leakage, and installation is not allowed.
2. Outdoor unit: the leak detection equipment shall be extended into the packing box of the outdoor unit, to
check whether the refrigerant is leaking. If the refrigerant leakage is identified, installation is not allowed, and the
outdoor unit shall be delivered to the maintenance department.
1. The room area checked cannot be less than the area specified on the warning sign of the indoor unit.
2. Inspection on the surrounding environment of place of installation: the outdoor unit of flammable
refrigerants air conditioner cannot be installed inside an enclosed room reserved.
3. Power supply, switches or other high-temperature articles such as the fire source and oil heater shall be
avoided below the indoor unit.
4. The power supply shall be provided with earthing wire and be reliably earthed.
5. While punching the wall with an electric drill, whether embedded water/electricity/gas pipelines are
designed at the hole preset by the user shall be verified in advance. It is recommended that the through-wall holes
reserved shall be used as much as possible.
1. Favorable ventilation shall be maintained at the place of installation (doors and windows are opened).
2. Open fire or high-temperature heat source (including welding, smoking and oven) higher than 548
is not
allowed within the scope of flammable refrigerant.
3. Anti-static measures shall be taken, such as the wearing of cotton clothes and cotton gloves.
4. The place of installation shall be convenient for installation or maintenance, and cannot be adjacent to heat
source and flammable and combustible environment.
5. In case of refrigerant leakage of the indoor unit during installation, the valve of the outdoor unit shall be
closed immediately, and windows shall be opened, and all the personnel shall be evacuated. After the leakage of
refrigerant is handled, the indoor environment shall be subject to concentration detection. Further handling is not
allowed until the safety level is reached.
6. In case the product is damaged, it must be delivered to the maintenance point. Welding of refrigerant
pipelines at the user’s site is not allowed.
7. The installation position of air conditioner shall be convenient for installation or maintenance. Barriers shall
be avoided around the air inlet/outlet of the indoor/outdoor unit, and the electrical appliance, power switches,
sockets, valuables and high-temperature products within the scope of both sidelines of the indoor unit shall be
avoided.
4
No fire source around the
place of installation
Read operator’ manual
Read technical manual
Operator’ manual；operating instructions
Cotton clothes Anti-static gloves
BEWARE
ELECTROSTATICS
Goggles
• Safety Awareness
• Unpacking Inspection
• Inspection on Installation Environment
• Safety Principles of Installation
'C
0
•
w
mJ
Содержание
- Contents 2
- Keep this manual where the user can easily find it 3
- Read the precautions in this manual carefully before operating the unit this appliance is filled with r32 3
- Warning 3
- 1 the factory refrigerant charge of the product 2 the additional refrigerant amount charged 4
- Cautio 4
- Contains fluorinated greenhouse gases covered by the kyoto protocol 4
- Important information rega rding the refrigerant used 4
- The field 1 4
- The filled out label must be adhered in the proximity of the product charging port e g onto the inside of the stop value cover a contains fluorinated greenhouse gases covered by the kyoto protocol b factory refrigerant charge of the product see unit name plate c additional refrigerant amount charged in the field d total refrigerant charge e outdoor unit f refrigerant cylinder and manifold for charging 4
- The total refrigerant charge 4
- This product contains fluorinated greenhouse gases covered by the kyoto protocol do not vent into the atmosphere refrigerant type r32 4
- The maximum refrigerant charge amount m 5
- And connecting pipes with inert gas 9
- Cleaning 9
- Disassembly 9
- Inspection on operational state 9
- Inspection on system leakage prior to disassembly 9
- Installation as required 9
- Refrigerant 9
- Refrigerant recovery by the system 9
- Safety discharge 9
- Standards 9
- The indoor 9
- Maintenance items 11
- Air inlet 14
- Air outlet 14
- Arrangement of piping directions 14
- Compressor inside of unit 14
- Connecting piping and electrical wiring 14
- Drain hose 14
- Fi gure are the 14
- Fixing of outdoor unit 14
- More than 10cm 14
- More than 20cm 14
- More than 30cm 14
- More than 60cm 14
- Non adhesive tape 14
- Optional parts for piping 14
- Parts numbers the indoor unit should be installed at the recommended height 1 m 14
- Piping hole cover 14
- Please be subjected to the actual product purchased 14
- Rear left left rear right 14
- Saddle l s with screws connecting electric cable for indoor and outdoor drain hose heating insulating material 14
- The marks from to in th 14
- The models adopt hfc free refrigerant r32 for installation of the indoor units refer to the installation manual which was provided with the units the diagram shows a wall mounted indoor unit 14
- When installing the unit to wall roof or rooftop fix a supporter surely with nails or wires in preparation of earthquake and strong wind 2 air conditioner mounted not above and one meter away from electric equipment such as television 14
- Fire explosion 15
- Fire or explosion 15
- Fire or explosion will be caused 15
- Safety precautions 15
- Before installing the unit 16
- For conventional hfc refrigerants will not work 16
- Safety precautions 16
- Iiiii j 17
- Warning caution n 17
- Do not use large capacity fuses steel wire or copper wire damaging the unit fire smoke or explosion will be caused otherwise 18
- Install a explosion proof breaker for current leakage at the power source to avoid the risk of the electric shock 18
- Safety precautions 18
- Without a breaker for current leakage will cause risks of electric shock fire or explosion 18
- And materials that must not used with 19
- Be used exclusively with not to be used if used with r22 19
- Caution install new pipes immediately after removing old ones to keep moisture out 19
- If there is a gas leak or if the remaining refrigerant is exposed to 19
- Items to be checked 19
- Necessary tools and materials 19
- Open flame a noxious gas hydrofluoric acid may form keep workplace well ventilated 19
- Prepare the following tools and materials necessary for installing and servicing the unit necessary tools for use with adaptability 19
- Read before installation 19
- Refrigerant used by the unit to be serviced refrigerant type 2 check the symptom exhibited by the unit to be serviced look 19
- Refrigerants such as r22 will cause the refrigerating machine oil to deteriorate 19
- Some types 19
- The refrigerant circuit chloride 19
- This document 4 19
- This service handbook for symptoms relating to the refrigerant cycle 3 be sure to carefully read the safety precautions at the beginning 19
- Tools and materials that are used with r22 or r407c that can also be used with 19
- Tools and materials that may be used with with some restrictions 19
- Tools for must be handled with special care and keep moisture and dust from entering the cycle 19
- Tools that are for use with r22 and r407c 19
- Verify the type 19
- C 19 5 20
- Hig_her 20
- R22 r407c 20
- Read before installation 20
- Read before installation 21
- A 170 mm c 130mm 22
- A 222mm c 165mm 22
- C j 61 22
- Installation dimension unit mm 22
- Connection of pipes 23
- Installation procedure 23
- Liquid pipe 23
- Piping size 23
- After finishing connection 24
- Air tightness test 24
- Check if the pressure drops if the pressure does not drop then pass if the pressure drops then please check the leaking point 24
- Checking the leaking point 24
- Each joint by listening touching and using soap water etc to identify the leaking point after confirming the leaking point welding it again or tighten the nut tightly again 24
- G a large leakage will be found 24
- G a small leakage will be found 24
- Installation procedure 24
- Mpa 0 kg c 24
- Order to prevent the nitrogen entering the circulation system 24
- Outdoor unit tighten the valve rod before giving pressure both gas and liquid valve rods 24
- Pressure it shall be corrected during test 24
- Pressurize for about 24 hours at 3 mpa 30 kg c 24
- Pressurize for over 3 minutes at 0 mpa 3 kg c 24
- Pressurize for over 3 minutes at 1 mpa 15 kg c 24
- Refrigerant pipe it shall perform air tightness test the air tightness test adopts nitrogen tank to give pressure according to the pipe connection mode as the following figure shown the gas and liquid valve are all in close state 24
- The ambient temperature will cause a variation of 24
- To 3 steps if the pressure drops check the leakage 24
- When pressurizing for 24 hours a variation 24
- ______ 24
- Installation procedure 25
- Wyv ivr 25
- Installation procedure 26
- Check if there is leakage in the unit 27
- Detect 27
- Lack of refrigerant 27
- Outdoor unit 27
- Suction temperature sensor failure when the the wiring of compressor is wrong or the connection is poor 27
- Troubleshooting 27
- Australia 1300 729 948 haier com au new zealand 0800 424 372 haier co nz 28
- Conditioning 28
Похожие устройства
- Haier 1U53WADFRA Инструкция по монтажу
- Haier 1U71WADFRA Инструкция по монтажу
- Haier AS09FBBHRA Инструкция по эксплуатации
- Haier AS12FBBHRA Инструкция по эксплуатации
- A4Tech Bloody B328 Инструкция по эксплуатации
- LEO LVR1-2 Инструкция по эксплуатации
- LEO LVR1-2 Сертификат
- LEO LVR1-2 Каталог
- LEO LVS1-2 Инструкция по эксплуатации
- LEO LVS1-2 Сертификат
- LEO LVS1-2 Каталог
- LEO LVR1-3 Инструкция по эксплуатации
- LEO LVR1-3 Сертификат
- LEO LVR1-3 Каталог
- LEO LVS1-3 Сертификат
- LEO LVS1-3 Инструкция по эксплуатации
- LEO LVS1-3 Каталог
- LEO LVR1-4 Инструкция по эксплуатации
- LEO LVR1-4 Каталог
- LEO LVR1-4 Сертификат