Centek CT-1801-60 Beige Инструкция по эксплуатации онлайн [11/24] 631323

Centek CT-1801-60 Beige Инструкция по эксплуатации онлайн [11/24] 631323
11
install the hood on the screws.
There are 2 holes with a diameter of 6 mm on the back panel of the
hood. Fix the hood to the wall with protective screws using these
holes. Install a flange on top of the hood.
MOUNTING UNDER A HINGED CABINET
ATTENTION! The air duct hole must be drilled at the bottom of the
cabinet. The second hole can be either in the upper part of the
cabinet or in its back wall, depending on how you have planned the
ventilation. You can also use any available types of pipe, both rigid
and soft, to divert air. Measure the distance at the bottom of the hood
mounting cabinet.
Drill four holes with a diameter of 6 mm, as shown in Figure 2. Install
the flange on the hood. Remove the protective film from the hood,
then screw the hood to the cabinet.
Both methods of installing the hood allow air drainage through the
rear duct. Before installing the hood, remove the factory-installed
protective panel from the rear opening. In this case, the exhaust
outlet on the wall should be exactly opposite the exhaust duct, the
flange is not installed (the rear air outlet is rectangular), and a plug
is installed on the upper air outlet. It is also permissible to use both
air vents at the same time - upper and rear. In this case, a flange
should be installed on the upper one. But in practice, one hole is quite
enough to carry out effective ventilation.
CIRCULATION MODE
Switching between the circulation and ventilation modes is carried
out using a lever (see Fig. 3).
In order for the hood to work in recirculation mode, air outlet plugs
must be installed.
5. CARE OF THE DEVICE
Disconnect the power cord from the mains and allow the engine
to cool down. Remove the anti-fat aluminum filters. Rinse them in
warm soapy water, then dry them and put them in the hood. This
procedure should be performed at least once a month. A filter
contaminated with grease is:
- Risk of fire. Oil stuck on the filter is flammable and can cause
a fire.
- Decrease in the efficiency of air drainage.
- Risk of failure of the device. Contaminated filters do not provide
sufficient air conductivity, which can cause engine overload.
Wash the hood regularly, removing all food residues, fat and other
contaminants. Wipe the outer surface only with a damp soft cloth
with the addition of detergent.
Storage and operation of the hood should be carried out in dry
heated rooms at a temperature not lower than + 5 °C and a relative
humidity of not more than 80%.
Transportation of the product should be carried out in accordance
with the marking indicated on the package. After transporting the
hood in conditions of low temperature, it is allowed to use the device
only after two hours of its stay in a warm room.
fig. 3
We apologize if the scope of delivery, dimensions, description,
technical characteristics, appearance or color of the product turned
out to be inaccurate. The manufacturer reserves the right to change
these parameters without prior notice, as a result of which, at the
time of purchase of a particular product, they may differ from those
indicated earlier.
6. POSSIBLE PROBLEMS AND WAYS TO FIX THEM
- Before contacting the service center, check the following: Make
sure that the hood is connected to the mains. Check the mains
voltage.
- By external inspection, check the integrity of the elements of the
electrical circuit, in case of malfunction of any element, contact
customer service.
Repairs should only be carried out by qualified service center
personnel! If your lamp has burned out, you can replace it yourself.
To do this, follow these steps:
1. Turn off the appliance and disconnect it from the mains.
2. Remove the lamp cover by unscrewing the 2 screws.
3. Remove the lamp.
4. Replace the lamp with a new one with a base of the same standard.
5. Assemble everything in reverse order.
7. ENVIRONMENTAL PROTECTION, DISPOSAL OF THE DEVICE
ENVIRONMENTAL PROTECTION
The packaging and the device itself are made of materials that can
be reused. If possible, when disposing of them, dispose of them in a
container intended for reusable materials.
DISPOSAL OF THE DEVICE
The device can be disposed of separately from ordinary household
garbage at the end of its service life. It can be handed over to a
special reception point for electronic devices and electrical
appliances for recycling. Materials are processed in accordance
with their classification. By handing over this device at the end of
its service life for recycling, you will make a great contribution to
environmental protection. You can get a list of points of reception
of electronic devices and electrical appliances for recycling from
municipal public authorities.

Содержание

Скачать