Home
Главная
Saturn
Термопот
ST-EK8036
Инструкция по эксплуатации Страница: 5

Saturn ST-EK8036 Инструкция по эксплуатации онлайн [5/48] 644319

To reboil water under keep warm

mode

1. Reboil a full tank of water will

take about 3 minutes.

2. Before re-boiling, make sure

the water level is above the “REFILL”

line. Refer to the water level indicator

for the marking.

3. The “REBOIL” button may not

function right after the water has boiled.

4. When adding water to the

water tank, be careful of the hot steam

while opening the lid.

5. Once the “REBOIL” button is

pressed, the boiling process cannot be

reset until the appliance automatically

switches to the “KEEP WARM” mode.

6. Do not press the “REBOIL”

button repeatedly, as the continuous re-

boiling process will cause malfunction to

the appliance.

When not in use

When the appliance is not in use, unplug

and remove the remaining water from

the water tank.

1. Press the manual pump to pour

out the remaining hot water slowly from

the water tank.

2. Allow the appliance to dry

thoroughly.

3. Do not place the appliance in a

dishwasher or dish dryer as this will

cause damage to the appliance.

4. If not in use, seal in a plastic

bag to protect it from dust and insects.

AUTO-CUT OFF FUNCTION

1. When the water boil-dry, the

appliance will automatically cut off the

power.

2. The auto cut-off function will

also operate when:

• The power is switched on, but

no water inside the water tank.

• Water level is below the

“REFILL” line. Refer to the water level

indicator for the marking.

CLEANING AND MAINTENANCE

1. Always allow the appliance to

cool down before cleaning.

2. Remember to unplug the

receptacle from the product body.

3. Detach the lid and pour out

remaining water.

4. If mineral deposits are allowed

to accumulate, loud noises may be

heard during boiling and you may face

difficulties in dispensing hot water.

Regular cleaning will avoid such

problems.

MAINTENANCE OF THE WATER TANK

Discoloration of the water tank and

white particles floating in the water.

Red rust-like spots, milky or black

discoloration on the water tank, and

white floating objects are caused by

minerals in the water and are not cause

by discoloration or deterioration of the

water tank itself.

Although this is not a hygiene problem,

it is advisable to clean the inner of the

water tank periodically.

1. Insert about 15-20g of store

brought citric acid into the water tank.

Add water until the water level reaches

full line marking. Close the lid.

NOTE: Do not fill the water more than

the full line marking. Please refer to the

maximum water level marking under

the product descriptions. If the

appliance is overfilled, it may cause

splashing, which might arise a hazard

to the user.

2. Connect the receptacle to the

appliance.

3. Connect the power plug to the

wall outlet. Power on the appliance.

3. Let the appliance boil. After the

boiling process, unplug from the wall

outlet. Wait until the appliance cools

down and then empty the water tank.

4. Remove the remaining water

by pressing the manual pump.

5. Cut a lemon into four pieces,

wrap the lemon in a clean cloth and

place it inside the water tank.

6. Fill water until the water level

reaches full line marking. Let the

appliance boil and retain the heat for

about one hour.

7. Pour out the water and use a

nylon brush to clean the water tank.

8. To remove the smell of the

lemon, fill the water until the water level

reaches the full line marking and boil

the water again, then dispose all the

boiled water.

Stainless steel water tank.

• Wash with a sponge and then

rinse with clean water.

IMPORTANT: Do not use the following to

clean the water tank.

• Dishwashing detergent (the

tank may be smelly), scrubbing powder

or brush, benzene, thinner or cleanser

(it will erode the water tank surface and

damage the plastic of the lid and inner

casing).

Saturn ST-EK8036 Инструкция по эксплуатации онлайн [5/48] 644319

Содержание

Похожие устройства