Skil 9176 LA Инструкция по эксплуатации онлайн [7/176] 92608
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 9176 LA Инструкция по эксплуатации онлайн [7/176] 92608

Skil 9176 LA Инструкция по эксплуатации онлайн [7/176] 92608
7
• Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintainafirmgriponthepowertoolandposition
yourbodyandarmtoallowyoutoresistkickback
forces.Alwaysuseauxiliaryhandle,ifprovided,for
maximumcontroloverkickbackortorquereaction
duringstart-up.The operator can control torque
reactions or kickback forces, if proper precautions are
taken.
b) Neverplaceyourhandneartherotatingaccessory.
The accessory may kickback over your hand.
c) Donotpositionyourbodyintheareawherepower
toolwillmoveifkickbackoccurs.Kickback will propel
the tool in the direction opposite to the wheel’s movement
at the point of snagging.
d) Usespecialcarewhenworkingcorners,sharp
edgesetc.Avoidbouncingandsnaggingthe
accessory.Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e) Donotattachasawchainwoodcarvingbladeor
toothedsawblade.Such blades create frequent
kickback and loss of control.
3)SAFETYWARNINGSSPECIFICFORGRINDINGAND
ABRASIVECUTTING-OFFOPERATIONS
a) Useonlywheeltypesthatarerecommendedfor
yourpowertoolandthespecificguarddesignedfor
theselectedwheel.Wheels for which the power tool
was not designed cannot be adequately guarded and are
unsafe.
b) Thegrindingsurfaceofthecentredepressed
wheelsmustbemountedbelowtheplaneofthe
guardlip. An improperly mounted wheel that projects
through the plane of the guard lip cannot be adequately
protected.
c) Theguardmustbesecurelyattachedtothepower
toolandpositionedformaximumsafety,sotheleast
amountofwheelisexposedtowardstheoperator.
The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.
d) Wheelsmustbeusedonlyforrecommended
applications.For example: Do not grind with the side of
a cut-o wheel. Abrasive cut-o wheels are intended for
peripheral grinding; side forces applied to these wheels
may cause them to shatter.
e) Alwaysuseundamagedwheelflangesthatareof
correctsizeandshapeforyourselectedwheel.
Proper wheel anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-o
wheels may be dierent from grinding wheel anges.
f) Donotuseworndownwheelsfromlargerpower
tools.A wheel intended for a larger power tool is not
suitable for the higher speed of a smaller tool and may
burst.
4)ADDITIONALSAFETYWARNINGSSPECIFICFOR
CUTTING OFF OPERATIONS
a) Donot“jam”thecut-offwheelorapplyexcessive
pressure.Donotattempttomakeanexcessive
depthofcut.Overstressing the wheel increases the
loading and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback or wheel
breakage.
b) Donotpositionyourbodyinlinewithandbehind
therotatingwheel.When the wheel, at the point of
operation, is moving away from your body, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
c) Whenthewheelisbindingorwheninterruptingacut
foranyreason,switchoffthepowertoolandholdthe
powertoolmotionlessuntilthewheelcomestoa
completestop.Neverattempttoremovethecut-off
wheelfromthecutwhilethewheelisinmotion,
otherwisekickbackmayoccur.Investigate and take
corrective action to eliminate the cause of wheel binding.
d) Donotrestartthecuttingoperationinthe
workpiece.Letthewheelreachfullspeedand
carefullyre-enterthecut.The wheel may bind, walk up
or kickback if the power tool is restarted in the workpiece.
e) Supportpanelsoranyoversizedworkpieceto
minimizetheriskofwheelpinchingandkickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Useextracautionwhenmakinga“pocketcut”into
existingwallsorotherblindareas.The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
5)SAFETYWARNINGSSPECIFICFORSANDING
OPERATIONS
a) Whensanding,donotuseexcessivelyoversized
sandingdiscpaper.Followthemanufacturers’
recommendationswhenselectingsandingpaper.
Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging,
tearing of the disc, or kickback.
6)SAFETYWARNINGSSPECIFICFORWIRE
BRUSHING OPERATIONS
a) Beawarethatwirebristlesarethrownbythebrush
evenduringordinaryoperation.Donotoverstress
thewiresbyapplyingexcessiveloadtothebrush.
The wire bristles can easily penetrate light clothing and/
or skin.
b) Iftheuseofaguardisrecommendedforwire
brushing,donotallowanyinterferenceofthewire
wheelorbrushwiththeguard.Wire wheel or brush
may expand in diameter due to work load and centrifugal
forces.
GENERAL
• This tool is not suitable for wet grinding/cutting
• Only use the anges which are supplied with this tool
• This tool should not be used by people under the age of
16 years
• Alwaysdisconnectplugfrompowersourcebefore
makinganyadjustmentorchanginganyaccessory
ACCESSORIES
• SKIL can assure awless functioning of the tool only
when original accessories are used
• Useonlygrinding/cuttingdiscswithamaximum
thicknessof8mmandaspindleholediameterof22
mm

Содержание

Похожие устройства

Скачать