Home
Главная
Maxwell
Утюг
MW-3027 W
Инструкция по эксплуатации Страница: 11

Maxwell MW-3027 W [11/32] English

ENGLISH

a sound signal. The unit will be switched on

automatically once you resume ironing.

• If the iron remains still for 8 minutes in ver-

tical position, the heating element of the

iron will be switched off, and you will hear

a sound signal. The unit will be switched on

automatically once you resume ironing.

WATER SELECTION

Use tap water to fill the tank. If tap water is hard,

it is recommended to mix it with distilled water

in proportion 1:1, if tap water is too hard, mix

it with distilled water in proportion 1:2 or use

distilled water only.

FILLING THE WATER TANK

Before filling the tank with water make sure that

the unit is unplugged.

– Set the temperature control knob (11) to the

“min” position, and the continuous steam

supply knob (3) to the

position (pic. 1).

– Open the water inlet lid (2).

– Pour the water into the water tank (10) with

the beaker (15) (pic. 2), then close the lid (2).

Notes:

• Do not fill the water tank (10) with scented

liquids, vinegar, starch solution, descaling

reagents, chemical agents etc.

• Do not exceed the “max” mark (13).

• If you need to refill water during ironing,

switch the iron off at first and unplug it.

IRONING TEMPERATURE

– Always check the recommended ironing

temperature indicated on the tag before

ironing.

– If there is no tag with recommended ironing

temperature, but you know the type of fab-

ric, use the following table to determine the

proper ironing temperature.

Icons of the ironing

temperature

Fabric type

(temperature)

•

Synthetics, nylon,

acrylic, polyester (low

temperature)

••

Silk/wool (medium

temperature)

•••

Cotton/linen (high

temperature)

max

Maximum temperature

– This table is only valid for smooth materials.

Other types of fabrics (crimped, raised etc.)

should be ironed at low temperature.

– Sort items by ironing temperature first: syn-

thetics with synthetics, wool with wool, cot-

ton with cotton etc.

– The iron heats up faster than it cools down.

For this reason it is recommended to begin

ironing at low temperature (for instance,

synthetic fabrics).

– After that, start ironing at higher tempera-

ture (silk, wool). Cotton and linen items

should be ironed last.

– If an item is made of mixed fabrics, the iron

should be set to the lowest ironing tempera-

ture (for instance, if an item is made of acryl-

ic and cotton, it should be ironed at temper-

ature used for acrylic ironing “•”).

– If you cannot define the fabric structure,

find a place that is hidden while wearing and

select the ironing temperature experimen-

tally (always start with the lowest tempera-

ture and raise it gradually until you get the

desired result).

– Corduroy and other fabrics that become

glossy quickly should be ironed strictly in

one direction (in direction of the pile) with

little pressure.

– To avoid appearance of glossy spots on syn-

thetic and silk fabrics, iron them backside.

SETTING THE IRONING TEMPERATURE

– Place the iron on its base (8).

– Insert the power plug into the mains socket.

– Turn the temperature control knob (11) to set

the required ironing temperature: «•», «••»,

«•••» or «max» (pic. 3), depending on the

type of fabric, the pilot lamp (9) will light up.

– Once the soleplate (14) reaches the set tem-

perature, the pilot lamp (9) will go out, you

can start ironing.

Note: - While the first switching on the heating

element of the iron burns, therefore occurrence

of foreign smell and a small amount of smoke is

possible, it is normal.

MW-3027.indd 11 03.06.2014 10:26:17

Maxwell MW-3027 W [11/32] English

Содержание

Похожие устройства