Hoover HYP1600 [5/9] Accessories and nozzles

Hoover HYP1600 [5/9] Accessories and nozzles
3
*Certain Models Only **Nozzle design may vary according to models
GB
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before
calling your local HOOVER service.
Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
Is the water tank or bin lled? Please refer to ‘Cleaner Maintenance’.
Is the Filter blocked? Please refer to ‘Cleaning the lter’.
Is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the system’.
IMPORTANT INFORMATION
HOOVER spares and Consumables
Always replace parts with genuine HOOVER spares. These are available from your local
HOOVER dealer or direct from Hoover. When ordering parts always quote your model
number.
Consumables:
Filter Kit (Pre-Motor and Exhaust): U72 35601577
Spares:
Carpet & Floor Nozzle: G150 35601579
Hard Floor Caresse Nozzle: G151 35601580
Pet Mini Turbo Nozzle: J51 35601163
Complete Flexible Hose: D148 35601578
Quality
HOOVER’s factories have been independently assessed for quality. Our products are
made using a quality system which meets the requirements of ISO 9001.
Your Guarantee
The guarantee conditions for this appliance are as dened by our representative in the
country in which it is sold. Details regarding these conditions can be obtained from the
dealer from whom the appliance was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of this guarantee.
Subject to change without notice.
Cleaning the pre-motor lter:
1. Press the bin release button and remove the bin assembly from the cleaner, by
holding the bin handle. [1]
2. Open the bin lid latch left/right and remove the water tank from bin assembly. [2]
3. Remove the pre-motor lter foam A and B. [18]
4. Wash it in hand warm water [23] and allow it to dry thoroughly before replacing to the
cleaner. [24]
5. Take out the pre-motor HEPA lter and remove the pre-motor lter foam. [19, 20]
6. Wash HEPA lter and lter foam [23] and allow it to dry thoroughly before replacing
to the cleaner. [24]
Cleaning the exhaust lter:
1. To remove the exhaust lter, unclip the exhaust lter cover and remove the exhaust
lter from the exhaust lter cover. [21]
2. Wash the lter in hand warm water [22, 23] and allow it to dry thoroughly before
replacing to the cleaner. [24]
NOTE: Do n
ot use hot water or detergents. In the unlikely event of the lters becoming
damaged, t a Genuine Hoover replacement. Do not try and use the product without lters
tted.
Removing a Blockage From the System
If the suction of the cleaner decreases:
1. Check if the water tank and bin are full. If so refer to ‘EMPTYING AND CLEANING
THE WATER TANK AND BIN CYCLONE AND BIN’.
2. If the water tank and bin are not full, then;
A. Do the lters need cleaning? If so refer to ‘Cleaning the Filter’.
B. Check if there is any other blockage in the system - Use a rod or a pole to remove
any blockage from Telescopic tube or exible hose.
ACCESSORIES AND NOZZLES
The crevice tool, furniture nozzle and dusting brush can be stored on the tube.
Crevice Tool
* – For corners and hard to reach areas. [X1]
Dusting Brush* – For bookshelves, frames, keyboards and other delicate areas.
[X2]
Furniture Nozzle – For soft furnishings and fabrics. [X3]
Carpet and Floor Nozzle**- For carpet and oors. [P]
Hard Floor Nozzle* – For parquet oors and other delicate oors. [AA]
Pet Hair Remover Mini Turbo Nozzle*– Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas.[Y]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. [Z]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.

Содержание

Похожие устройства

Скачать