Home
Главная
Al-Ko
Райдер
R 7-63.8 A
Руководство по эксплуатации Страница: 42

Al-Ko R 7-63.8 A Руководство по эксплуатации онлайн [42/272] 779329

42 R7-62.5 | R7-63.8 A | R7-65.8 HD

Operating the ride-on mower

■

Keep the driving speed low.

■

Do not drive across the slope.

■

Do not accelerate suddenly.

■

Steer smoothly.

7.6 Mowing with the ride-on mower

Adapt the driving speed to the conditions of the

lawn in order to achieve a tidy mowing result. Se-

lect a maximum of 2/3 of the possible driving

speed for mowing. The maximum speed of the

ride-on mower is exclusively intended for driving

without the mower mechanism switched on.

Normally, the cutting height is 4 - 5 cm. This cor-

responds to the 2nd or 3rd detent of the height

adjustment (03/C). Please mow with a higher cut-

ting height if the grass is moist or wet.

If the grass is very long, it is a good idea to mow

in two passes. Set the mower mechanism to the

maximum cutting height on the first pass. You

can reduce it to the required height for the sec-

ond pass.

7.6.1 Switching on the mower mechanism

NOTE

Do not switch on the mower mechanism

until the engine has been running for

about one minute to warm up!

The ride-on mower should not be stand-

ing in high grass when the mower mech-

anism is engaged.

Precondition: The engine is running and the en-

gine speed controller (03/C) is in the operating

position (see chapter 7.4 "Starting and shutting

off the engine", page40).

1. Set the uppermost cutting height with the ad-

justing lever (09/2).

Note:The mower mechanism must always

be started at the uppermost cutting height.

2. Pull the lever (10/1) for switching on the

mower mechanism upwards (10/a) and en-

gage it (10/b). The mower mechanism is run-

ning.

3. Set the required cutting height with the ad-

justing lever (09/2).

4. Moving off with the ride-on mower:

■

Manual transmission: see chapter 7.5.1

"Starting off and stopping with manual

transmission", page41

■

Foot hydrostat transmission: see chapter

7.5.2 "Starting off and stopping with foot

hydrostat transmission", page41

7.6.2 Mowing in reverse

WARNING!

There is an accident risk when re-

verse mowing!

Pay attention to the area behind you

when mowing in reverse!

Only mow in reverse when it is neces-

sary to do so!

7.6.2.1 Reverse mowing with manual

transmission

As soon as the mower mechanism is engaged

(i.e. also when stationary), the reverse gear is

completely blocked. For reverse mowing (i.e. re-

versing with the mower mechanism engaged),

however, the reverse gear can be released with

the release lever:

1. Brake the ride-on mower to a standstill from

forwards mowing by depressing the brake/

clutch pedal (05/1).

■

Move the selector lever (07/2) to the N

position.

2. Raise the release lever (07/1) on the selector

lever.

3. Move the selector lever (07/2) from the N po-

sition to the R position.

4. For reverse mowing, slowly release the

brake/clutch pedal (05/1).

NOTE

Engaging the mower mechanism when

reversing is not intended due to safety

reasons. Therefore, always start reverse

mowing from the ride-on mower's sta-

tionary position. If you nevertheless at-

tempt to engage the mower mechanism

when reversing, the selector lever auto-

matically moves to the N position and

the reverse gear is blocked.

7.6.2.2 Reverse mowing with foot hydrostat

transmission (21)

On engaging the mower mechanism, the pedal

for reversing is limited to a maximum speed of

1.08km/h. Up to this speed, reverse mowing can

also be carried out at any time by depressing the

reverse pedal.

1. During forwards mowing:

■

Relieve the forwards pedal (21/1)

■

Depress the brake pedal (21/2) until the

ride-on mower is stationary.

Al-Ko R 7-63.8 A Руководство по эксплуатации онлайн [42/272] 779329

Содержание

Похожие устройства