Home
Главная
Rondell
Утюг
RDE-2000
Инструкция по эксплуатации Страница: 10

Rondell RDE-2000 Инструкция по эксплуатации онлайн [10/24] 810715

ENGLISH

• Do not use the iron after it was dropped, if there is visible

evidence of damage or if the iron is leaking.

• Do not attempt to repair the unit by yourself. Do not disas-

semble the unit by yourself, if any malfunction is detected or

after it was dropped, unplug the unit and contact any autho-

rized service center from the contact address list given in

the warranty certificate and on the website www.rondell.ru.

• Transport the unit in the original packaging only.

• Keep the unit out of reach of children and people with dis-

abilities.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. COM-

MERCIAL USE AND USE IN PRODUCTION AREAS OR WORK

SPACES IS PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage under cold (winter)

conditions, it is necessary to keep it for at least 3 hours

at room temperature before switching on.

• Unpack the iron; remove the protection (if any) from the

iron soleplate (11).

• Check the unit for damages; do not use the iron in case

of damages.

• Before switching the iron on, make sure that your home

mains voltage corresponds to the iron operating voltage.

• The unit is intended for operation with AC system and

50 or 60 Hz frequency, the unit does not need any additional

settings for operating with the required nominal frequency.

• There may be water residue in the tank, this is nor-

mal, as the iron has undergone factory quality control.

Note: during the first use, the heating element of the iron may

undergo some charring, which could result in a slight odor

and a small amount of smoke. This is a normal occurrence.

WATER SELECTION

Use tap water to fill the water tank. If tap water is hard, it is

recommended to mix it with distilled water in proportion 1:1,

if tap water is too hard, mix it with distilled water in proportion

1:2 or use distilled water only.

FILLING THE WATER TANK

Before filling the iron with water, make sure that it is un-

plugged.

• Set the temperature control knob (12) to the position

«MIN», and the continuous steam supply knob (3) to the

position « ».

• Open the water inlet lid (2).

• Pour water into the water tank (10) using the beaker (15)

and then close the lid (2).

Notes:

– Do not exceed the «max» mark (14).

– If you need to refill water during ironing, switch the iron off

and unplug it.

– After you finish ironing, switch the unit off, wait until it cools

down completely, then open the water inlet lid (2), turn over

the iron and drain the remaining water.

IRONING TEMPERATURE

Before operation, test the heated iron on a piece of cloth to

be sure that the iron soleplate (11) and the water tank (10) are

clean.

• Always check the recommended ironing temperature indi-

cated on the tag before ironing.

• If there is no tag with recommended ironing temperature,

but you know the type of fabric, refer to the following table

to determine the proper temperature.

FABRIC TYPE ICONS (TEMPERATURE)

•

Synthetics, nylon, acrylic, polyester (low temperature)

••

Silk/wool (medium temperature)

•••

(МАХ)

Cotton/linen (high temperature)

• This table is only valid for smooth materials. Fabrics of

other types (crimped, raised, etc.) are best ironed at a low

temperature.

• Sort your garments according to the ironing temperature

first: separate synthetic fabrics, wool, cotton, and so on.

• The iron heats up faster than it cools down. For this rea-

son, it is recommended to begin ironing at low temperature

(for instance, synthetic fabrics). Then proceed to ironing at

higher temperatures (silk/wool). Cotton and linen garments

should be ironed last.

• If an item is made of mixed fabrics, the iron should be set

to the lowest ironing temperature (for instance, if an item is

made of polyester and cotton, it should be ironed at tem-

perature used for polyester ironing «•»).

• If you cannot determine the composition of the fabric, find

an inconspicuous spot and select the ironing temperature

through trial and error (always start with the lowest tem-

perature and raise it gradually until you get the desired

result).

• Corduroy and other fabrics that become glossy quickly

should be ironed strictly in one direction (in the direction of

the pile) with gentle pressure.

• To avoid appearance of glossy spots on synthetic and silk

fabrics, iron them backside.

Rondell RDE-2000 Инструкция по эксплуатации онлайн [10/24] 810715

Похожие устройства