Vitek VT-8355 Инструкция по эксплуатации онлайн [10/36] 811776
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-8355 Инструкция по эксплуатации онлайн [10/36] 811776

Vitek VT-8355 Инструкция по эксплуатации онлайн [10/36] 811776
10
ENGLISH
vision of a person who is responsible for their
safety or if they are not instructed by this person
on the usage of the unit.
•
Do not use the unit if the power cord or the plug
is damaged, if the unit works improperly or after
it was dropped or in case of leakage.
•
Do not use the unit if the power plug or the
power cord is damaged. If the power cord is
damaged, it should be replaced by the manu-
facturer, maintenance service or similar quali-
fied personnel to avoid danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
•
Unpack the iron; remove the protection from the
soleplate (14), if any.
•
Check the unit for damages, do not use the iron
in case of damages.
•
Before switching the iron on, make sure that
your home mains voltage corresponds to the
iron operating voltage.
•
There may be water residue in the tank, this is
normal, as the iron has undergone factory qual-
ity control.
Note: While the first switching on the heating ele-
ment of the iron burns, therefore occurrence of
foreign smell and a small amount of smoke is pos-
sible, it is normal.
WATER SELECTION
You can use tap water to fill the water tank (10).
If tap water is hard, use distilled or demineralized
water, this will prolong service life of the iron.
Note: Do not fill the water tank (10) with scented liq-
uids, vinegar, starch solution, descaling reagents,
chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that
it is unplugged.
• Set the temperature control knob (11) to the
position «MIN», and the continuous steam
supply knob (5) to the position « » – contin-
uous steam supply is off.
• Open the lid (2) and pour water into the water
tank (10) using the beaker (15) and then close
the lid (2) tight.
Note:
• Do not exceed the «MAX» mark (13).
• If you need to refill water during ironing,
always switch the iron off first and unplug it.
• After you finish ironing, switch the iron off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece
of cloth to be sure that the iron soleplate (14) and
the water tank (10) are clean.
• Always check the recommended ironing tem-
perature indicated on the tag before ironing.
• If the item label is marked with the symbol
, do not iron the item.
• If there is no tag with recommended ironing
temperature, but you know the type of fab-
ric, use the following table to determine the
proper temperature.
Ironing temperature table
Icons Fabric type (temperature)
do not iron
•
Synthetics, nylon, acryl, polyester
(low temperature)
••
Silk/wool (medium temperature)
•••
Cotton (high temperature)
МАХ
Linen (high temperature)
• This table is only valid for smooth materials.
Fabrics of other types (crimped, raised, etc.)
are best ironed at low temperature.
• Sort items by ironing temperature first: syn-
thetics to synthetics, wool to wool, cotton to
cotton etc.
• The iron heats up faster than it cools down.
For this reason, it is recommended to iron
the items which require low temperature
first (for instance, synthetic fabrics). After

Похожие устройства

Скачать