Home
Главная
Vitek
Паровая Станция
VT-2433
Инструкция по эксплуатации Страница: 10

Vitek VT-2433 Инструкция по эксплуатации онлайн [10/36] 811786

ENGLISH

• For children safety reasons do not leave poly-

ethylene bags, used as packaging, unattended.

Attention! Do not allow children to play with poly-

ethylene bags or packaging film. Danger of suf-

focation!

• Do not allow children to touch the steam station

body, the steam hose, the power cord or the

power plug during operation of the unit.

• Do not leave children unattended to avoid them

using the unit as a toy.

• Close supervision is necessary when children

or people with disabilities are near the operat-

ing unit.

• This unit is not intended for usage by children.

• During the operation and breaks between oper-

ation cycles, keep the unit away from children.

• The unit is not intended to be used by peo-

ple with physical, sensory or mental disabilities

(including children) or by persons lacking expe-

rience or knowledge if they are not under super-

vision of a person who is responsible for their

safety or if they are not instructed by this person

on the usage of the unit.

• From time to time check the power cord integrity.

• Do not use the unit if the power cord or the

power plug is damaged, if the unit works improp-

erly and after it was dropped.

• If the power cord is damaged, it should be replaced

by the manufacturer, maintenance service or simi-

lar qualified personnel to avoid danger.

• Do not use the unit after dropping in case of vis-

ible damage or leakage.

• Do not repair the unit by yourself. Do not dis-

assemble the unit by yourself, in case of any

malfunctions, as well as after the unit has been

dropped, disconnect the unit from the mains

and contact any authorized service center at the

contact addresses indicated in the warranty card

and on the website www.vitek.ru.

• To avoid damages, transport the unit in original

package only.

• Keep the unit in a dry darkened and cool place

out of reach of children and disabled persons.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE

ONLY. ITS COMMERCIAL USAGE AND USAGE

IN PRODUCTION AREAS AND WORK SPACES IS

PROHIBITED.

WATER SELECTION

Use tap water to fill the tank. If tap water is hard,

it is recommended to mix it with distilled water in

proportion 1:1, if tap water is too hard, mix it with

distilled water in proportion 1:2 or use distilled wa-

ter only.

BEFORE THE FIRST USE

After unit transportation or storage at low tem-

perature keep it for at least three hours at room

temperature before switching on.

• Unpack the steam station and remove all pack-

aging elements that can prevent proper unit

operation.

• Press the unlock button (5) to release the iron

lock (4) and remove the iron from the steam sta-

tion base (1).

• Remove all labels, stickers or packaging from

the iron and the soleplate, if necessary.

• Wipe the soleplate of the iron with a clean, soft

cloth.

• Wipe the body of the iron and steam station base

(1) with a soft cloth.

• Make sure that the voltage of the mains corre-

sponds to the operating voltage of the unit.

• Place the steam station on a flat steady heat-

and water-resistant surface, so that the unit is

on the same level with your ironing board. When

setting the steam station on the ironing board,

make sure that the ironing board is secure and

steady.

• There may be water residue inside the tank, this

is normal, as the steam station has undergone

factory quality control.

FILLING THE WATER TANK

• Take into account that when you install the tank

back on the base, the water level will be above

the «MAX» mark. This doesn’t affect the steam

station performance.

• Do not add anything to the water and do not use

water with any additives. When water turns into

steam, chemicals, perfumes, and other addi-

tives coat the inner part of the steam chamber,

reducing the lifespan of the iron.

• Remove the water tank (2). To do that, push the

water tank lock (3) upwards and, using the front

handle of the water tank, extract the water tank

from the steam station base (1) (Fig. 1).

• Fill the water tank up to the «MAX» maximum level

mark. Do not exceed the maximum level mark.

• Reinstall the water tank (2) onto the base (1). To

do that, push the water tank lock (3) upwards,

and while holding it in the upward position, first

fully insert the bottom part of the water tank, fol-

lowed by the top part then release the lock (3)

(Fig. 1).

Vitek VT-2433 Инструкция по эксплуатации онлайн [10/36] 811786

Похожие устройства