Home
Главная
Vitek
Отпариватель
VT-2438
Инструкция по эксплуатации Страница: 10

Vitek VT-2438 Инструкция по эксплуатации онлайн [10/28] 811789

ENGLISH

• To switch the steam supply on, press and hold

the button (8). The water pump will switch on

and you will hear a distinctive sound. It is nor-

mal. To switch the steam supply off, release the

button (8).

• To switch the continuous steam supply mode on,

fix the steam supply button (8) in the lower posi-

tion. To switch the continuous steam supply off,

set the button (8) to the upper position.

Note: - do not direct the steam on metal buttons or

accessories.

ATTENTION!

During the operation, the operating surface (6)

and the upper part of the body (7) become very

hot, do not touch the operating surface (6) and

the upper part of the body (7), and beware of

getting burned by hot steam.

If you use the garment steamer without the brush

attachment (5), keep the operating surface (6)

at at least 5 cm from the clothes.

• Slowly run the steamer down the fabric, straight-

en the folds on the fabric with your free hand. Do

not place your hand under the steamed fabric

while switching the steam supply on.

• When steaming the clothes sleeves, start from

the top of the sleeve and move the steamer down.

Straighten the sleeve downwards and diagonally

with your free hand.

• When smoothing pockets on a shirt, move the

steamer up.

• After you finish using the unit, to switch the

steamer off, press and hold the on/off button (10)

for 2 seconds, the steamer will switch off, the light

indicator will go out. Unplug the unit.

• Remove the water tank (3), open the lid (2) and

drain the remaining water, install the tank (3) back

to its place.

Note: - After steaming the clothes should cool down

and dry, it may take some time.

Automatic switch off function

The garment steamer has two automatic switch off

options:

1. If the steamer is installed vertically and is not

used, in this case, after 8 minutes, the auto

switch-off function will be on, the heating ele-

ment will switch off and the light indicator will be

flashing.

2. The operation time of the garment steamer in the

steam supply mode is 20 minutes. After that the

auto switch-off function will be on, the heating el-

ement will switch off and the light indicator will be

flashing.

• To resume the operation, press the on/off button

(10) once.

• Wait until the light indicator glows constantly and

continue using the steamer.

USING THE BRUSH ATTACHMENT

ATTENTION!

Before installing the brush attachment (5), make

sure that the operating surface (6) has cooled

down and that the power plug is not connected

to the mains.

• The brush attachment (5) removes lint and

dirt from the clothes, makes smoothing of

the folds easier and allows to steam thick and

heavy fabrics.

• Install the brush attachment (5) on the operat-

ing surface (6), make sure that the brush attach-

ment (5) is fixed properly.

• To switch the steam supply on, press and hold

the button (8). The water pump will switch on

and you will hear a distinctive sound. It is nor-

mal. To switch the steam supply off, release the

button (8).

• To switch the continuous steam supply mode on,

fix the steam supply button (8) in the lower posi-

tion. To switch the continuous steam supply off,

set the button (8) to the upper position.

• After you finish using the unit, to switch the

steamer off, press and hold the on/off button

(10) for 2 seconds, the steamer will switch off,

the light indicator will go out. Unplug the unit.

• Remove the brush attachment (5).

• Remove the water tank (3), open the lid (2) and

drain the remaining water, install the tank (3)

back to its place.

USING THE LID WITH A PLASTIC BOTTLE

• If necessary, you can use a regular plastic

bottle (with capacity up to 0.33 l) as the water

tank (3).

• Fill the plastic bottle with water, put the water in-

take pipe in the bottle and close the lid (4) turn-

ing it clockwise.

• Place the lid (4) on the steamer body and turn it

clockwise as far as it will go.

CLEANING AND MAINTENANCE

• Disconnect the power plug from the mains sock-

et and let the garment steamer cool down com-

pletely.

• Remove the water tank (3), open the lid (2) and

drain the remaining water, install the tank (3)

back to its place.

• Clean the garment steamer body and the

operation surface (6) with the steam release

openings with a slightly damp cloth, and then

wipe dry.

• You can remove the mineral deposits from the

operating surface (6) with a cloth soaked in the

water and vinegar solution.

• Remove the brush attachment (5) and wash it

under a water jet.

• Do not use abrasive cleaners and solvents to

clean the garment steamer.

• Do not immerse the steamer, the power cord and

the power plug into water or other liquids.

STORAGE

• Unplug the steamer and wait till it cools down

completely.

• Clean the steamer.

• Keep the unit in a dry cool place out of reach of

children and disabled persons.

Vitek VT-2438 Инструкция по эксплуатации онлайн [10/28] 811789

Похожие устройства