Home
Главная
Coolfort
Конвектор
CF-3940
Инструкция по эксплуатации Страница: 9

Coolfort CF-3940 Инструкция по эксплуатации онлайн [9/28] 811805

ENGLISH

• Pay close attention when the unit is being used near

children or people with disabilities.

• This unit is not intended for usage by children. Keep

the unit out of reach of children during operation or

cooling down.

• The unit is not intended to be used by people with

physical, sensory or mental disabilities (includ-

ing children), or by persons lacking experience or

knowledge if they are not under the supervision of

a person who is responsible for their safety or if

they are not instructed by this person on the usage

of the unit.

• Do not leave the operating unit unattended.

• Unplug the unit if it is not being used and before

cleaning.

• Do not pull on the power cord to unplug the unit from

the mains, grasp the power plug with your hand and

remove it from the mains.

• Do not touch the power plug with wet hands.

• Make sure that the power cord does not come into

contact with hot surfaces or sharp furniture edges.

• Do not wind the power cord around the unit body.

• Check the power cord insulation integrity from time

to time.

• If the power cord is damaged, it should be replaced

by the manufacturer, a maintenance service or simi-

lar qualified personnel to avoid danger.

• Do not attempt to repair the unit. Do not disassemble

the unit by yourself, if any malfunction is detected or

after it was dropped, unplug the unit and apply to any

authorized service center from the contact address

list given in the warranty certificate and on the web-

site www.coolfort.ru.

• Transport the unit in the original package only.

• Keep the unit out of reach of children and disabled

persons.

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.

ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION

AREAS AND WORK SPACES IS PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low tem-

perature keep it for at least three hours at room

temperature.

ATTENTION! The product is intended as an additional

heating device for the air in indoor spaces only. This

product is not intended as a main heating device.

• Remove the unit from its factory packaging and keep

the packaging.

• Study the manual and check the delivery set.

• Check the unit for damages, do not use it in case of

damages.

• Make sure that the unit operating voltage corre-

sponds to the voltage of your mains.

• The unit is intended for operation with AC system and

50 or 60 Hz frequency. The unit does not need any

additional settings for operating with the required

nominal frequency.

SETTING

Floor installation

• Turn the unit over.

• Install the support legs (1) matching the ledge on the

convector with the latch on the leg until the lock dis-

tinctive clicking (pic. 1).

• Turn the convector over and put it on the support

legs (1).

• Make sure that the unit is placed on an even surface.

REMOTE CONTROL

ATTENTION! The remote control (22) uses a lithium

battery. Keep the lithium battery away from children to

prevent it from being swallowed. If a child swallows

the battery, seek medical attention immediately.

• Press on the side of the lock and remove the battery

holder (27), install a CR2025 battery, strictly follow-

ing the polarity.

• Reinstall the battery holder (27).

Notes: if there is an insulating film pad present, remove

it from the battery holder (27).

Battery replacement

• Remove the battery holder (27), remove the old bat-

tery, install a new CR2025 battery strictly following

the polarity, install the battery holder (27) into the

remote control (22).

• Do not throw away used batteries with regular house-

hold waste. Dispose of them at a specialized collec-

tion point for further recycling.

CONVECTOR USAGE

• Before switching the unit on, make sure that your home

mains voltage corresponds to the unit operating volt-

age, and the power switch (3) is in the «Off» position.

• Insert the power plug into the mains socket.

SWITCHING ON THE CONVECTOR

• Switch on the convector by using the power switch

(3) - you will hear a sound signal and the unit will

go into standby mode. The on/off button (14) « »

indication will light up on the control panel (5), and

the digital symbols (15) will show the temperature

inside the room where the convector is placed, and

the symbol (16) «°C» will light up.

• Press the on/off button (7) « » on the control

panel (5) or the button (23) « » on the remote

control (22), the convector will switch on and the

flashing digital symbols (15) will show the set room

temperature, and then the numbers will stop flash-

ing and will glow constantly, the room temperature

will be displayed and the symbol (16) «°C» will light

up. After some time the temperature indication, the

symbol (16) «°C» and the symbol (14) « » will go

out and the current mode symbol (18, 19, 20 or 21)

will be displayed.

Note: temperature readings on the indicator may

differ slightly from the readings of other temperature-

measuring devices.

Coolfort CF-3940 Инструкция по эксплуатации онлайн [9/28] 811805

Похожие устройства