Fubag FС 230/24 CM2 230 л/мин, 24л, 8бар, 1.5кВт, 61431378 [10/16] Operator s manual

Содержание

• Operator s manual 1
• Инструкция по эксплуатации 1
• Operator s manual 2
• Page01 2
• Page02 3
• Page03 4
• Page04 5
• Operator s manual 6
• Page05 6
• Safety operation 6
• Caution 7
• Not to do 7
• Operator s manual 7
• Page06 7
• Operator s manual 8
• Page07 8
• Start up and use 8
• Technical specifications 8
• Maintenance 9
• Operator s manual 9
• Page08 9
• Operator s manual 10
• Page09 10
• Troubleshooting 10
• Warranty 10
• Page10 11
• Инструкция по эксплуатации 11
• Ипад 11
• Правила безопасности 11
• Page11 12
• Важно 12
• Гипад 12
• Запрещается 12
• Инструкция по эксплуатации 12
• Page12 13
• Инструкция по эксплуатации 13
• Пуск и эксплуатация 13
• Технические характеристики 13
• Шрад 13
• Page13 14
• Инструкция по эксплуатации 14
• Техническое обслуживание 14
• Page14 15
• Гарантийные обязательства 15
• Гиьад 15
• Инструкция по эксплуатации 15
• Неисправности и способы их устранения 15
• Cover 2 16

Похожие устройства

• Fubag FС 230/24 CM2 230 л/мин, 24л, 8бар, 1.5кВт, 61431378 Инструкция по эксплуатации
• Fubag Smart Air 646032 Инструкция по эксплуатации
• Fubag Smart Air + набор из 6 предметов Инструкция по эксплуатации
• Fubag VB 4000B/100 CM3 61431377 Инструкция по эксплуатации
• Fubag VCF/100 CM3 45681472 Инструкция к компрессору FUBAG VCF/100 CM3 45681472
• Fubag VCF/50 CM3 45681465 Инструкция к компрессору FUBAG VCF/50 CM3 45681465
• Fubag VDC 400/50 CM3 400 л/мин, 50л, 8бар, 2.2кВт 614319554 Инструкция по эксплуатации
• Garage PK 24.F250/1.5 8142210 Инструкция к компрессору Garage PK 24.F250/1.5 8142210
• Garage PK 50.MBV400/2.2 8087900 Инструкция к компрессору Garage PK 50.MBV400/2.2 8087900
• HDC HD-A103 Инструкция к товару
• HDC HD-A203 Инструкция к товару
• Калибр КМК-2100/50У 00000060251 Инструкция к товару
• Komprem 0505000 Паспорт поршневого блока KRW-7.5/11.0
• Metalmaster MCDR 7.5-10-500 21021 Инструкция
• Metalmaster MCDR 7.5-10-500 21021 Инструкция
• Бежецк АСО К-20 2536 Инструкция к компрессору Бежецк АСО К-30 2559
• AMR Glazing Tornador A-21 Инструкция к товару
• Бежецк АСО К-2 2535 Инструкция к компрессору Бежецк АСО К-30 2559
• LIKSIR 201402 ТДС
• Nordberg поршневой NC500/1200 Инструкция

fubag Operator s manual www fubag ru 5 Troubleshooting Request the assistance of a qualified electrician for operations on electric components cables motor pressure switch electric panel etc FAULT CAUSE REMEDY Leakage of air from the valve of the pressure switch with the compressor off Check valve that due to wear or dirt on the seal does not perform its function correctly Unscrew the hexagonal head of the check valve clean the valve seat and the special rubber disk replace if worn Reassemble and tighten carefully figures 14a 14b Reduction of performance Frequent start up Low pressure values Excessive performance request check for any leaks from the couplings and or pipes Intake filter may be clogged Replace the seals of the fitting clean or replace the filter The compressor stops and restarts automatically after a few minutes Tripping of the thermal cutout due to overheating of the motor Clean the air ducts in the conveyor Ventilate the work area Reset the thermal cutout On lubricated check oil level and quality After a few attempts to restart the compressor Tripping of the thermal cutout due to overheating of the motor Activate the on off switch Ventilate the work area Wait a few minutes The compressor will restart independently Remove any power cable extensions The compressor does not stop and the safety valve is tripped Irregular functioning of the compressor or breakage of the pressure switch Remove the plug and contact the Service Center Any other type of operation must be carried out by authorized Service Centers requesting original parts Tampering with the machine may impair its safety and in any case make the warranty null and void 6 Warranty Warranty refer to defects of materials and components and do not refer to components subject to natural wear and maintenance work Only machines cleaned from dust and dirt in original factory packing fully completed provided with instruction manual warranty card with fixed sales date with a shop stamp factory serial number and originals of sales and ware receipt issued by salesman are subjects of warranty Within the warranty period the service center eliminate free of charge all detected production defects The manufacturer disclaims warranty and legal responsibilities if nonobservance of the instruction manual by user unqualified disassembling repair or maintenance of the machine as well does not bear responsibility for caused injury to persons or damages 9