ENDA (Турция) ATP4LVS0830 ATP4LVS0830 онлайн
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

ENDA (Турция) ATP4LVS0830 ATP4LVS0830 онлайн

ENDA (Турция) ATP4LVS0830 ATP4LVS0830 онлайн
ENDA ATP4 MULTI FUNCTIONAL ANALOG TIMER
Thank you for choosing ENDA ATP4 Multi Functional Analog Timer
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury , material damage or capital disadvantages.
Connection Diagram
ENDA ATP4 is intended for installation in control panels. Make sure that the device is used only for intended
purpose. The electrical connections must be carried on by a qualified staff and must be according to the relevant
locally applicable regulations. During an installation, all of the cables that are connected to the device must be
free of electrical power. The device must be protected against inadmissible humidity, vibrations, severe soiling.
Make sure that the operation temperature is not exceeded. All input and output lines that are not connected to the
supply network must be laid out as shielded and twisted cables. These cables should not be close to the power
cables or components. The shielding must be grounded on the instrument side.
Technical Specifications
CONTROL
Timing function
A, B, C, D, E, F Modes can be selected on device.
Switch inputs for 10 screw-terminal or 11 pin octal connector models. (Pulsing time min. 3ms.)
Timing unit
Start input
OUTPUTS
ENVIRONMENTALCONDITIONS
Height
Maximum 2000m
80% Relative humidity for temperatures up to 31°C, decreasing linearly to 50% at 40°C.
Ambient/storage temperature
Relative humidity
0 ... +50°C/-25 ... 70°C (There shouldn't be icing or condensation on the environment.)
Supply voltage
90-250V AC, 50/60Hz or 24V AC/DC, 50/60Hz
Power consumption
Maximum 10VA
8/11pins octal connector or 7/10 pins screw-terminal.
Depending on the effect of supply voltage : max %0.2
Connection
Scale
Reset time
Accuracy
EN 61326-1: 2006
EN 61010-1: 2010 (pollution degree 2, over voltage category II)
ELECTRICALCHARACTERISTICS
0-1.2 , 0-3 , 0-12 , 0-30 or 0-60.
0.3 Seconds for ATP4-UV, 0.01 seconds for ATP4-LV.
Rated pollution degree
According to EN 60529 Front panel : IP50
Rear panel : IP20
Relay: 250V AC, 8A (resistive load), NO
Control output (OUT2)
Relay: 250V AC, 8A (resistive load), NO+NC
Do not use the device in locations subject to corrosive and flammable gasses.
HOUSING
Housing type
Suitable for flush-panel mounting or rail mountable 8/11 pin octal connector.
Dimensions
W48xH48xD82mm
Weight
Approx. 170g (after packing)
Enclosure metarial
Self extinguishing plastics
48mm
14mm
67mm
82mm
38mm
45mm
48mm
Dimensions
Note :
Panel thickness
should be
maximum 3mm.
Panel cut-out
51mm
60mm
46mm
46mm
1) Mains supply cords shall meet the requirements of IEC
60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply
switch shall bring the identification of the relevant
instrument and it should be easily accessible by the
operator.
SUPPLY :
NOTE :
90-250V AC /
(24V AC/DC)
Switch
Cable size : 1,5mm²
Fuse
F 100 mA 250V AC
Fuse should
be connected
2
1
1
For removing the device
from the panel:
- Push in the mounting clamps
in direction 1.
- Then, pull out the device
in direction 2.
Control output
state indicator
Power
indicator
Trigger output (OUT1)
38mm
45mm
1
1
2
Connection
cables
8/11 pin octal
connector
7/10 Screw-terminal
Connector
Timing unit Timing mode
Supply
90-250V AC
or
(24V AC/DC)
Gate input
Reset input
Second, 10 seconds, minute, 10 minutes, hour, 10 hours units can be selected on device.
EMC
Safety requirements
Depending on the set value settings : max %5
Depending on the effect of temperature : max %1
CONTACT
250V AC 8A
RESISTIVE
LOAD
INDUSTRIAL ELECTRONICS
ENDA
ATP4-UV-K10-03 ANALOG TIMER
SN: XXXXXXXXX
8 680407 709175
Made in Turkey
7
6
5
4
3
2
1
OU
T2
OUT
1
8
9
1
0
RESET
GATE
START
S
U
PPLY
9
0
-
250
V
AC
50/6
0
H
z
1
0
VA
CONTACT
250V AC 8A
RESISTIVE
LOAD
INDUSTRIAL ELECTRONICS
ENDA
ATP4-LV-S11-12 ANALOG TIMER
SN: XXXXXXXXX
8 680407 709434
Made in Turkey
OUT2
1
OUT1
2
3
4
5
6
7
8
9
10
11
GATE
START
RESET
SUPPLY
24V AC/DC
50/60Hz 10VA
CONTACT
250V AC 8A
RESISTIVE
LOAD
5
4
3
2
1
INDUSTRIAL ELECTRONICS
ENDA
ATP4-UV-K07-01 ANALOG TIMER
SN: XXXXXXXXX
S
U
PPLY
90-2
5
0
V
A
C
50
/
6
0
H
z
10
V
A
OUT
2
O
UT
1
6
7
8 680407 709069
Made in Turkey
CONTACT
250V AC 8A
RESISTIVE
LOAD
INDUSTRIAL ELECTRONICS
ENDA
ATP4-LV-S08-30 ANALOG TIMER
SN: XXXXXXXXX
8 680407 709342
Made in Turkey
1
OUT1
2
3
4
5
6
7
8
OUT2
SUPPLY
24V AC/DC
50/60Hz 10VA
Insulation test voltage
3kV AC min. 1 minute, 4,2kV DC min. 1 minute.
1 / 2
CONTACT
250V AC 8A
RESISTIVE
LOAD
INDUSTRIAL ELECTRONICS
ENDA
ATP4-LV-S08-30 ANALOG TIMER
SN: XXXXXXXXX
8 68 0 4 0 7 7 0 9342
Made in Turkey
1
OUT1
2
3
4
5
6
7
8
OUT2
SUPPLY
24V AC/DC
50/60Hz 10VA
CONTACT
250V AC 8A
RESISTIVE
LOAD
5
4
3
2
1
INDUSTRIAL ELECTRONICS
ENDA
ATP4-UV-K07-01 ANALOG TIMER
SN: XXXXXXXXX
SU
P
P
LY
9
0-
2
50
V
A
C
5
0/
60
Hz 1
0V
A
OU
T2
OU
T1
6
7
8 68 0 4 0 7 7 0 9069
Made in Turkey
0 30
5
10
15
20
25
S
10S
M
10M
H
10H
A
B
C
D
E
F
ATP4
ENDA
PWR
OUT
0 30
5
10
15
20
25
S
10S
M
10M
H
10H
A
B
C
D
E
F
ATP4
ENDA
PWR
OUT
* 48 x 48mm sized.
* Triggering whit supply voltage.
* Triggering output (OUT1).
* Contact output for timing function (OUT2).
* 6 Different timing modes for OUT2 (A, B, C, D, E, F).
* 6 Different timing unit selections for OUT2 (S,10S, M, 10M, H, 10H).
* Suitable for 8/11 pin octal or 7/10 screw-terminal connection.
* Start, reset and gate inputs for 10 pins screw-terminal or 11 pin octal connector.
* CE marked according to European Norms.
Life expectancy for relay
Without load 30.000.000 operation; 250V AC, 8A resistive load 100.000 operation.
Control output state
OUT Led lights up when there is power at the output control, it is flashes as long as the timer is running.
Switch inputs for 10 screw-terminal or 11 pin octal connector models. (Pulsing time min. 3ms.)
Switch inputs for 10 screw-terminal or 11 pin octal connector models. (Pulsing time min. 3ms.)
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
+
-
+
-
+
-
ORDER CODE
7 Pins screw-terminal
10 Pins screw-terminal
8 Pins octal
11 Pins octal
Skala
01 0 ... 1,2
03 0 ... 3
12 0 ... 12
30 0 ... 30
60 0 ... 60
90-250V AC
24V AC/DC
UV
LV
K07
K10
S08
S11
ATP4 - xV - xxx - xx
Supply Voltage
Product Basic Code
Panel Mounted
Multi Function Analog Timer
Connection Type
ENDA
TM
ATP4-xV-xxx-xx-EN-03-220103

Похожие устройства

Скачать