DWT SDS-MAX BH16-42 VB BMC Инструкция по эксплуатации онлайн [37/228] 830451
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

DWT SDS-MAX BH16-42 VB BMC Инструкция по эксплуатации онлайн [37/228] 830451

DWT H13-05 B BMC Инструкция по эксплуатации онлайн [37/228] 666831
37
English
• insert (slightly twisting) the borer (chisel) into
the chuck 1 (SDS PLUS) or into the chuck 22
(SDS MAX) against stop (see g. 9.2);
• release xing bush 3 (see g. 9.3);
• test the borer (chisel) xing by trying to remove
it from chuck 1 (SDS PLUS) or from chuck 22
(SDS MAX)�
• When removing borer (chisel):
• move xing bush 3 back and hold it in this position
(see g. 10.1);
• extract the borer (chisel) from the chuck 1
(SDS PLUS) or from chuck 22 (SDS MAX) (see
g. 10.2);
• release xing bush 3 (see g. 10.3).
[H12-06 B]
• Move backward the xing bush 3 and hold it in this
position (see g. 11.1).
• Mount / replace the accessory� When installing the
working accessory, it is necessary to clear the shank
end preliminarily (see g. 11.2)�
• Release the xing bush 3 (see g. 11.3).
Gloves are to be used when removing the
borer (chisel) from chuck, as the borer
(chisel) may be dangerously hot after
long drilling.
Replacing the dust protection casing (see g. 12)
[BH10-26 B, BH10-28 VB, BH12-28 VB, BH13-32 VB,
BH15-32 VB, BH15-36 VB, BH16-42 VB, H13-05 B,
H17-11 B]
Dust protection casing 2 prevents the
dust from entering the SDS PLUS chuck
or SDS MAX chuck. Never use your power
tool with a damaged dust protection cas-
ing 2 - if damaged, it must be immediately replaced.
You can either do it on your own, or contact the
DWT service center.
• Move xing bush 3 back and hold it in that position
(see g. 12.1).
• Pull dust protection casing 2, and remove it (see
g. 12.2).
• Install a new dust protection casing 2 (see g. 12.3).
• Release xing bush 3 (see g. 12.4).
Adapter for chuck SDS PLUS
[BH10-26 B, BH10-28 VB, BH12-28 VB, BH13-32 VB,
BH15-32 VB, BH15-36 VB]
• SDS PLUS adapter 25 and screw 26 enable using
gear rim chuck 24�
• Never use SDS PLUS adapter 25 in the impact drill-
ing or chiselling operation modes�
• Drills that don't belong to the SDS PLUS system are
not allowed for the impact drilling�
Mounting / dismounting of the gear rim chuck (see
g. 13-14)
[BH10-26 B, BH10-28 VB, BH12-28 VB, BH13-32 VB,
BH15-32 VB, BH15-36 VB]
• Screw the gear rim chuck 24 onto the adapter 25
(SDS PLUS) and lock it in with the screw 26 (see g. 13).
• Install the adapter 25 (SDS PLUS) into the
chuck 1 (SDS PLUS), repeating the same steps as
when mounting the borer (chisel) see g. 14.
• When dismantling, repeat the steps described
above in the reverse order�
Attention: keep in mind that in the pro-
cess of mounting / dismounting of the
gear rim chuck 24 the screw 26 has a left-
hand thread.
Mounting / replacement of accessories (see g. 15)
[BH10-26 B, BH10-28 VB, BH12-28 VB, BH13-32 VB,
BH15-32 VB, BH15-36 VB]
• Release the cams grip with drill chuck key 27, then
rotate the quill of gear rim chuck 24 counter-clockwise
with your hand (see g. 15) until the cams move apart
at the distance allowing an accessory to be mounted /
replaced�
• Mount / replace an accessory�
• Rotate the quill of gear rim chuck 24 clockwise with
your hand in order to lock the accessory mounted� Do
not allow the accessory to become distorted�
• Tighten the cams of gear rim chuck 24 with drill
chuck key 27 applying a similar torque to each of the
three openings on the side surface of the chuck�
With long-term use the drill bit may be-
come very warm; use gloves to remove
it.
•
Initial operation of the
power tools
Always use the correct supply voltage the power
supply voltage must match the information quoted on
the power tool identication plate.
• The power tool is supplied properly lubricated and
ready for use�
• A new power tool needs some time for its parts to
run in before a full load operation� The run-in period
duration is about 5 hours of operation�
• The gear lubrications require a short time to get warm�
Depending on the ambient temperature this period of
time can alter within the range of approximately 15 s
(at ambient temperature of 32°С) up to 2 minutes (at
ambient temperature of 0°С).
Switching the power
tool on / off
[BH10-26 B, BH10-28 VB, BH12-28 VB, BH13-32 VB,
BH15-32 VB, BH15-36 VB, BH16-42 VB]
Switching on:
Press on / off switch 11�
Switching off:
Release the on / off switch 11�
[H12-06 B, H13-05 B]
Short-term switching on / off
To switch on, press and hold on / off switch 11, to
switch off - release it�

Содержание

Похожие устройства

Скачать