Home
Главная
Efco
Бензопилы
MT 4510 41 см 50239154E2
Инструкция Пила бензиновая EFCO MT 4510 (41 см) Страница: 30

Efco MT 4510 41 см 50239154E2 Инструкция Пила бензиновая EFCO MT 4510 (41 см) онлайн [30/214] 830966

RUS

EST

1. Clean surface around fuel cap to prevent

contamination.

2. Loosen fuel cap slowly.

3. Carefully pour fuel mixture into the tank.

Avoid spillage.

4. Prior to replacing the fuel cap, clean and

inspect the gasket.

5. Immediately replace fuel cap and hand

tighten. Wipe up any fuel spillage.

WARNING: Check for fuel leaks, if any

are found, correct before use. Contact a

Servicing Dealer if necessary.

OIL FILLING AND CHAIN LUBRICATION

The saw chain is automatically lubricated during

use by a pump which normally requires no

maintenance. The oil flow is pre-regulated by the

manufacturer to ensure a sufficient oil delivery

even under heavy working conditions. During

cutting of thin timber a possible oil dripping is

normal.

- Always wipe off around the filler hole before

unscrewing the cap (13, Fig. 2) so that no dirt

enters the oil reservoir.

- During work watch the oil level.

- After the filling, operate the motor 2 or 3 times

to restore correct oil delivery.

- In case of faults do not try to repair the

machine yourself, but apply to your authorized

dealer.

Correct chain lubrication during the cutting

phase reduces wear to a minimum between the

chain and bar thus prolonging life. Always use a

good quality oil.



WARNING - Never use waste oil.

Always use biodegradable lubricant (eco-

lube Oleo-Mac/Efco) which is specific for bar

and chain and also respectful towards nature,

operator health and chain saw’s parts.

Before starting make sure the chain is not

obstructed.



When the chainsaw is running, grip the

front handle firmly with your left hand

and the back handle with your right hand

(Fig. 11).

- Do not lean forward and do not cut above

shoulder height; gripping the chain saw at the

top of the handle makes it difficult to control

and counteract kickback.

- Check that all parts of the body are kept

away from the chain and muffler.

- Left-handers should follow these

instructions too. Keep a proper cutting

stance.



Over exposure to vibrations can result in

blood-vessel or nerve injury to persons

suffering with blood circulation problems.

Seek medical attention if you experience

physical symptoms such numbness, lack of

feeling, reduction in normal strength, changes

in the color of the skin. These symptoms

normally appear in the fingers, hands or

wrists.

Engine is Flooded

- Set the on/off switch to STOP (B,Fig.13).

- Unscrew the screw on the cover (A,Fig.27).

- Remove the cover.

- Pry off the spark plug boot.

- Unscrew and dry off the spark plug.

- Open the throttle wide.

- Pull the starter rope several times to clear the

combustion chamber.

- Refit the spark plug and connect the spark

plug boot, press it down firmly.

- Set the on/off switch to I, the starting position.

- Set the choke lever to OPEN position – even if

engine is cold.

- Now start the engine.



WARNING – Never start the saw engine

without the bar, chain and clutch cover

(chain brake) assembled - or else the clutch can

come loose and cause personal injuries.

STARTING THE ENGINE

The chain brake must be engaged when

starting the saw. Set the chain brake by

pushing the chain brake lever / hand guard

forward (towards the bar), to the brake

position (Fig. 12). Fill the carburetor by pushing

primer bulb (A, Fig. 14A). Push the choke lever, (B,

Fig.14A) fully down (1). Place the chainsaw on the

ground in a stable position. Check that the chain

is free to turn and will not come into contact with

any foreign objects. Before you start the engine,

make sure the saw chain is not contacting any

Efco MT 4510 41 см 50239154E2 Инструкция Пила бензиновая EFCO MT 4510 (41 см) онлайн [30/214] 830966

Похожие устройства