NEO Tools 89x165 мм 14-018 Инструкция 14-018 онлайн [4/16] 831529

that exceed their rated speed. Wear helmet when working above your head. Be careful and watch out for rotating parts even after releasing the

start and stop trigger. Make sure the material processing does not cause fire.

Hazards related to repetitive movements

When using a pneumatic tool for operation that involves repetitive moves, the operator is exposed to discomfort of hands, arms, shoulders, neck

and other body parts. When using a pneumatic tool, keep comfortable body posture that ensures the right feet position and avoid uneasy or

unbalanced body postures. Change your body posture when working for a long time, it helps to avoid discomfort and fatigue. When experiencing

constant or recurring discomfort, pain, pulsating pain, tingling, numbness, burning sensation or stiffness, do not ignore the symptoms, inform your

employer and consult a doctor.

Hazards related to accessories

Disconnect the tool from power supply before changing the working tool or an accessory. Avoid direct contact with the working tool during and

after operation, it may be sharp or hot. Use accessories and consumables only in sizes and types recommended by the manufacturer. Do not use

accessories of other types or other sizes. Make sure the maximum operating speed of the working tool is higher than the rated speed of the device.

Never install grinding wheels, grinding discs or mills on the sander. Grinding disc cracking may cause serious body injuries or even death. Never

use wheels with dents, damages or when dropped. Make sure to use tools with correct mounting diameter. Notice that speed allowed at installation

point is lower due to increased shaft length between collet end and the installation point. Make sure that minimum installation length is 10 mm.

Bear in mind the risks when the working tool diameter does not match the collet diameter.

Workplace related hazards

Slipping, tripping and falling are the main reasons of injuries. Avoid slippery surfaces when using the tool and tripping hazards caused by

compressed air system. Be careful in unknown environment. There may be hidden dangers, such as electricity or other utility systems. The

pneumatic tool is not designed for use in explosion hazardous areas and has no electric insulation. Make sure there are no electric wires, gas

pipes etc. that may be dangerous when damaged with the tool.

Dusts and fumes related hazards

Dusts and fumes produced with the pneumatic tool may cause bad health condition (e.g. cancer, congenital defects, asthma and/or dermatitis), so

the risk assessment is necessary, and implementation of appropriate control measures for the hazards. The risk assessment should include impact

of dust produced with the tool and possibility to stir up and lift existing dust. Operate and maintain the pneumatic tool in accordance with the

instruction manual, which allows to minimise unnecessary emission of vapours and dusts. Air outlet should be directed in a way to minimise stirring

up dust in dusty environment. Wherever dust and fumes are produced, it is a priority to control the emission at the source. All integrated functions

and equipment used for collection, extraction and reduction of dust or smoke should be used appropriately and maintained in accordance with the

manufacturer's guidelines. Select, maintain and replace working tools in accordance with the guidelines in the manual to prevent increased vapours

and dusts production. Use respiratory tract protection in accordance with the employer instructions, as well as occupational health and safety rules.

Processing certain materials produces dusts and fumes, which can form potentially explosive environment.

Noise hazards

Exposure to high noise without any protection may cause permanent and irreversible hearing loss and other problems, such as tinnitus (sensation

of ringing, buzzing, whistling or humming in ears). Risk assessment is necessary, and implementation of appropriate control measures related to

the hazards. Appropriate control aiming to reduce risks can include measures such as silencing materials to prevent “ringing” of processed piece.

Use hearing protection in accordance with the employer instructions, as well as occupational health and safety rules. Operate and maintain the

pneumatic tool in accordance with the instruction manual, which allows to prevent unnecessary increase of noise. Select, maintain and replace

worn out working tools in accordance with the instruction manual. It will prevent unnecessary increase of noise. When the pneumatic tool is

equipped with a muffler, always make sure it is installed properly when operating the tool.

Vibration hazards

Exposition to vibrations may cause permanent injuries of nervous and vascular systems in hands and arms. Wear warm clothes when working in

low temperatures and keep your hands warm and dry. In case of numbness, tingling, pain or whiteness of skin on fingers or hands, stop using the

pneumatic tool, inform your employer and consult a doctor. Operation and maintenance of the pneumatic tool in accordance with instruction manual

allows to avoid unnecessary increase of vibrations. Select, maintain and replace consumables and working tools in accordance with the guidelines

in the manual to prevent hazardous increase of vibrations. Support the tool weight with a stand, tensioner or with a balancer. Vibration hazards

are usually higher with stronger hand grip, therefore hold the tool with light but firm grip, while considering reaction forces that may appear. Incorrect

installation of cutting tool may cause increase of vibration level.

Additional safety instructions regarding pneumatic tools

Pressurised air may cause serious injuries:

− always cut off air supply, release air pressure from the hose and disconnect the tool from air supply at all times, when the tool is not

in use, before changing accessories or before repairs;

− never direct air stream at yourself or another person.

Hitting with a hose may cause serious injuries. Always inspect the equipment for damaged or loose hose and connectors. Make sure to direct cold

air away from hands. Each time when universal rotation joints are used (claw couplings), use securing pins and securing fasteners that protect

from damages between hoses and between a hose and the tool. Do not exceed maximum air pressure specified for the tool. Never carry the tool

when holding by its hose.

EXPLANATION OF USED SYMBOLS

18. Read instruction manual, observe warnings and safety conditions therein!

19. Use personal protection measures (protective goggles, earmuff protectors, anti-dust mask).

20. Use protective gloves.

21. Protect the tool from moisture.

22. Keep the tools away from children.

23. Recycling.

INSTALLATION DIAGRAM

24. Pneumatic tool

25. Quick coupler

26. Pneumatic hose

27. Oiler

28. Pressure regulator

29. Draining filter

30. Cut off valve

NEO Tools 89x165 мм 14-018 Инструкция 14-018 онлайн [4/16] 831529

Похожие устройства