Home
Главная
Ryobi
Рейсмусы
RAP1500G 5133002859
Инструкция к Ryobi RAP1500G Страница: 10

Ryobi RAP1500G 5133002859 Инструкция к Ryobi RAP1500G онлайн [10/236] 838655

English

FR DE ES IT NL PT DA SV FI NO RU PL CS HU RO LV LT ET HR SL SK EL TR UK

■ Set the blade heights according to the instructions in

"SETTING THE BLADE HEIGHT". The blade height

must be reset every time the blades are taken out for

any reason.

■ Be sure to replace the dust chute after blades are

installed.

SETTING THE BLADE HEIGHT

See gure 13-14.

■ To obtain a blade projection of 1.1 mm, place the

blade setting gauge on the cutterhead with both

guides resting firmly against the blade.

■ Loosen the assembly by turning the seven forcing

screws clockwise with an open end wrench.

■ When the blade is pressed to the required height

by guides on the gauge, retighten the assembly by

turning the forcing screws counter clockwise. Make

sure all seven forcing screws are tightened securely.

WARNING

The blade edge is very susceptible to chipping. Use

caution when handling the gauge near the blades to

avoid damaging them.

WARNING

The assembly must be tightened securely to prevent

accidents during planing.

CONNECTING A DUST COLLECTION SYSTEM

See gure 19.

The dust produced when using this tool may be harmful

to health. Use a dust absorption system and remove

deposited dust thoroughly, e.g., with a vacuum cleaner.

To connect a dust collection system:

■ Unplug the tool.

■ Connect the nozzle of the dust collection system to

the dust chute.

Clean the hose of the dust collection system frequently to

avoid the accumulation of dust.

ADJUSTMENT

MAKING THE CUTTERHEAD AND WORK TABLE PAR-

ALLEL

See gures 15-18.

Plane a workpiece and measure the thickness after the

cut. If the thicknesses are different on both sides of the

workpiece, perform the following:

Adjust the cutter shaft and the worktable so they are

parallel. The tools used for checking are shown in gure

15. Use hardwood to make a tool gauge block according

to the size shown in the gure. Make the adjustments as

per the following procedures.

■ Remove the height adjustment crank handle and

both top and side covers by removing allen screws to

expose the height adjustment lock nuts.

■ Loosen the adjustment lock nuts.

■ Adjust the height adjustment lock nuts up or down as

required to suit the gauge block.

■ When the desired height setting is reached, tighten the

lock nuts in position.

■ Reassemble side and top covers and replace the

height adjustment crank handle.

NOTE: Remove gauge block before starting machine.

Thickness planing is the sizing of the material to a desired

thickness, while creating a smooth surface parallel to the

opposite side of the board.

The art of thickness planing consists mainly of using good

judgement about the depth of cut in various situations.

You must take into account:

1. The width of the timber

2. The hardness of the timber

3. The dampness of the timber

4. The straightness of the board

5. The grain direction

6. The grain structure

How these factors can affect the quality of the work can

only be learned through experience. Whenever working

with a new type of wood, or one with unusual problems,

always make test cuts on scrap material prior to working

on the actual piece.

FOR ADDITIONAL PLANING

If additional planing is needed to obtain the desired

thickness of nish, hand crank the cutterhead no more

than 3 mm (at any given time) and complete another pass.

WARNING

Never plane more than 3 mm in one pass and never

attempt to plane a board under 127 mm (5") in length.

Always wear a protective face shield.

Ryobi RAP1500G 5133002859 Инструкция к Ryobi RAP1500G онлайн [10/236] 838655

Похожие устройства