Hikoki WR25SE WR25SENSZ Инструкция к товару онлайн [4/92] 841738
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hikoki WR25SE WR25SENSZ Инструкция к товару онлайн [4/92] 841738

Hikoki WR25SE WR25SENSZ Инструкция к товару онлайн [4/92] 841738
4
English
1. Switch operation (Fig. 3)
The switch (2) in this machine functions as a motor
switch and rotational direction selector switch. When
the switch is set to R indicated on the handle cover, the
motor rotates clockwise to tighten the bolt.
When the switch is set to L, the motor rotates
counterclockwise to loosen the bolt. When the switch is
released, the motor stops.
2. Operating time
Thetighteningtorqueincreaseswhentheoperatingtime
increases.Butthetighteningtorquedoesnotincrease
above a certain value even if the tool is driven for a long
time (See Fig. 5).
3. The protection function
To protect the tool, the protection function will be
activated, automatically shutting down the unit in the
event of any problems. (Table 1)
Table 1
Cause of Shutdown
Automatic shutdown initiated by excessive load (*1)
Automaticshutdowninitiatedduetothetool’sinternal
temperatureexceedingthespeciedtemperaturelevel(*2)
*1 Excessive load protection function
For excessive load conditions, the tool will shutdown to
prevent damage.
Discontinue the heavy load task, unplug the power
supply cord from the electrical outlet and plug it back in
to reset.
*2 Increased temperature protection function
Automatic shutdown is activated to prevent damage
from high temperatures.
The tool’s internal temperature will increase for tasks
involving the use of large currents of electricity, or when
used in high temperature environments.
Please allow the tool to rest for 10 to 15 minutes before
continuing a task.
MAINTENANCE AND INSPECTION
1. Inspecting the socket
Awornordeformed hex orasquare-holed socket will
notgiveanadequatetightnesstothettingbetweenthe
nutoranvil,consequentlyresultinginlossoftightening
torque.Payattentiontowearofsocketholesperiodically,
and replace with a new one if needed.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Replacing supply cord
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specic regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
toaHiKOKIAuthorizedServiceCenter.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue:—Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may
not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black. The wire
coloured brown must be connected to the terminal marked
with the letter L or coloured red. Neither core must be
connected to the earth terminal.
NOTE:
This requirement is provided according to BRITISH
STANDARD2769:1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841anddeclaredinaccordancewithISO4871.
Measured A-weighted sound power level:
106 dB (A) (WR22SE)
108 dB (A) (WR25SE)
Measured A-weighted sound pressure level:
95 dB (A) (WR22SE)
97 dB (A) (WR25SE)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
accordingtoEN62841.
Impact tightening of fasteners of the maximum capacitiy of
the tool:
Vibration emission value
a
h
= 15.2 m/s
2
Uncertainty K = 1.5 m/s
2
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
○ Thevibration emission during actual use of the power
toolcandierfromthedeclaredtotalvaluedependingin
the ways in which the tool is used.
○
Identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions
of use (taking account of all parts of the operating cycle
suchasthetimeswhenthetoolisswitchedoandwhenit
is running idle in addition to the trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the specications herein are subject to
change without prior notice.
0000Book_WR22SE.indb 4 2019/03/05 16:33:36

Похожие устройства

Скачать