STATUS BS75M 3140401 Инструкция к товару онлайн [3/26] 842219
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

STATUS BS75M 3140401 Инструкция к товару онлайн [3/26] 842219

STATUS BS75 3140301 Инструкция к товару онлайн [3/26] 842218
4
1. GENERAL SAFETY RULES
that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
• Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
SERVICE
• Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained
EN
5
2. ADDITIONAL SAFETY RULES FOR BELT SANDERS
• Hold power tool by insulated gripping surfaces, because the belt may
contact its own cord. Cutting a “live” wire may make exposed metal parts of the
power tool “live” and shock the operator.
• Always wear eye and ear protection and use a dust mask.
The dust and abrasive particles separated during operation may seriously injure
your health.
• Always remove the plug from the mains socket before making any
adjustments or maintenance, including changing the sanding belt.
• While operating the machine, always hold it firmly with both hands and
provide for a secure stance. The power tool is guided more securely with both
hands.
• Use the machine for dry sanding only. Penetration of water into the machine
increases the risk of an electric shock.
• Do not use worn, torn or heavily clogged sanding belts. Damaged sanding
belts can tear apart, be thrown from the machine and injure somebody.
• Fully unwind cable drum extensions to avoid potential overheating.
• When an extension cable is required, you must ensure that it has the right ampere
rating for your power tool and is in safe electrical condition.
• The outer metal parts and the bits may get hot after continuous operation. Do not
touch the bit or the work piece immediately after operation - they may be extremely
hot and you may get serious burns.
• After long working periods external metal parts and accessories could be hot.
• If possible, always use clamps or a vice to hold your work.
• Apply the machine to the workpiece only when switched on and switch
the machine off only after it has been lifted away from the workpiece.
• Always switch off before you put the sander down.
• Apply slight pressure during operation. The machine own weight is sufficient for
good sanding performance. Excessive increase of pressure does not increase
sanding capacity, but causes motor overheating and belt wear.
• The dust, separated while processing materials, containing quartz (SiO2) is
dangerous to your health. Do not process materials containing asbestos.
• When sanding wood, always connect the dust bag or use a dust extraction system.
• Before using the sander with metal, always remove the dust bag from the outlet as
sparks may ignite the dust or the bag.
• Do not touch the moving sanding belt.
• Ensure that you have removed foreign objects such as nails and screws from the
work before commencing sanding.
• Rags, cloths, cord, string and the like should never be left around the work area.
• Before using the tool on an actual work piece, switch on and let it run for a while.
Operate the tool at least 200 mm away from your face and body.
WARNING: Before connecting a tool to a power source (mains socket power point
receptacle, outlet, etc.) be sure that the voltage supply is the same as that specified
on the nameplate of the tool.
ADDITIONAL SAFETY RULES FOR BELT SANDERS
EN

Похожие устройства

Скачать