Dewalt 54 В XR FLEXVOLT два диска 125 мм DCG200NT-XJ Инструкция к товару онлайн [8/56] 842572

English

h ) Do not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If power tool

or wheel is dropped, inspect for damage or install an

undamaged wheel. After inspecting and installing

the wheel, position yourself and bystanders away

from the plane of the rotating wheel and run the

power tool at maximum no load speed for one

minute. Damaged wheels will normally break apart

during this testtime.

i ) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron capable

of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtering particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearingloss.

j ) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken wheel may fly away and cause

injury beyond immediate area ofoperation.

k ) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting

accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and could give the

operator an electricshock.

l ) Never lay the power tool down until the accessory

has come to a complete stop. The spinning wheel

may grab the surface and pull the power tool out of

yourcontrol.

m ) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

n ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

o ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel. Pinching or snagging causes rapid stalling of the rotating

wheel which in turn causes the uncontrolled power tool to be

forced in the direction opposite of the wheel’s rotation at the point

of thebinding.

For example, if a abrasive blade is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive blades may also

break under theseconditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking

proper precautions as givenbelow.

a ) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided,

for maximum control over kickback or torque

reaction during start-up. The operator can control

torque reactions or kickback forces, if proper precautions

aretaken.

b ) Never place your hand near the rotating accessory.

Accessory may kickback over yourhand.

c ) Do not position your body in line with the rotating

wheel. Kickback will propel the tool in direction opposite

to the wheel’s movement at the point ofsnagging.

d ) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control

orkickback.

e ) Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

blades create frequent kickback and loss ofcontrol.

f ) Do not "jam" the wheel or apply excessive pressure.

Do not attempt to make an excessive depth of

cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheelbreakage.

g ) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the wheel

from the cut while the wheel is in motion otherwise

kickback may occur. Investigate and take corrective

action to eliminate the cause of wheelbinding.

h ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

i ) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the line

of cut and near the edge of the workpiece on both sides

of thewheel.

j ) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can causekickback.

Additional Safety Information

• Use of accessories not specified in this manual is not

recommended and may be hazardous. Use of power

Dewalt 54 В XR FLEXVOLT два диска 125 мм DCG200NT-XJ Инструкция к товару онлайн [8/56] 842572

Похожие устройства