Dewalt 54 В XR FLEXVOLT два диска 125 мм DCG200NT-XJ Инструкция к товару онлайн [9/56] 842572

English

Chargers

DeWALT

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your

DeWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.



WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

boosters that would cause the tool to be driven at speeds

greater than its rated speed constitutesmisuse.

• Do not use circular saw blades with this tool. Serious

injury mayresult.

• Avoid bouncing the wheel or giving it rough treatment.

If this occurs, stop the tool and inspect the wheel for cracks

orflaws.

• Direct sparks away from operator, bystanders or

flammable materials. Sparks may be produced while using

a sander, grinder, or wall chaser. Sparks may cause burns or

startfires.

• Always use front handle. The front handle should always be

used to maintain control of the tool at alltimes.

• Never cut into area that may contain electrical wiring or

piping. Serious injury mayresult.

• Clean out your tool often, especially after heavy use.

Dust and grit containing metal particles often accumulate on

interior surfaces and could create an electric shockhazard.

• Do not operate this tool for long periods of time.

Vibration caused by tool action may be harmful to your

hands and arms. Use gloves to provide extra cushion and

limit exposure by taking frequent restperiods.

• Dust, crystalline material, vapor and smoke may be

produced while working. Always wear a dust mask or

respiratory protection. Danger forhealth!

• Never install more than two diamondblades.

• Use only diamond-tipped cutting discs. Segmented

diamond wheels may only have negative cutting angles and

slots between the segments to a maximum of 10mm.

Dewalt 54 В XR FLEXVOLT два диска 125 мм DCG200NT-XJ Инструкция к товару онлайн [9/56] 842572

Похожие устройства