Makita LXT BL 18 В, 460 Вт, D-рукоятка, d-30 см, M10xLH, разборвал (BL1830B DC18RC) DUR192LRF Инструкция по эксплуатации онлайн [18/52] 851294

18 ENGLISH

Electric brake

This tool is equipped with an electric brake. If the tool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at our service center.

CAUTION: This brake system is not a substi-

tute for the protector. Never use the tool without

the protector. An unguarded cutting tool may result

inseriouspersonalinjury.

Electronic function

Constant speed control

The speed control function provides the constant rota-

tion speed regardless of load conditions.

Soft start feature

Soft start because of suppressed starting shock.

ASSEMBLY

WARNING: Always be sure that the tool is

switched o󰀨 and battery cartridge is removed

before carrying out any work on the tool. Failure to

switcho󰀨andremovethebatterycartridgemayresult

inseriouspersonalinjuryfromaccidentalstart-up.

WARNING: Never start the tool unless it is

completely assembled. Operation of the tool in a

partially assembled state may result in serious per-

sonalinjuryfromaccidentalstart-up.

CAUTION: Do not disassemble the tool once

you have installed all the main components.

Installing main components

Pipe assembly

CAUTION: Avoid cutting the cable tie (nylon fas-

tener) away until the folded pipes have been securely

assembled.

1. Straighten the two-folded pipes, and then align the

stopper pin on the upper pipe with the stopper hole in

thejoint.

►Fig.9: 1. Upper pipe 2. Stopper hole 3. Stopper pin

4. Joint

Inserttheupperpipeintothejointwhileholdingdown

the stopper pin. Make sure that the pin pops up through the

stopper hole and securely locks the lower pipe.

►Fig.10: 1. Lower pipe 2. Stopper hole 3. Stopper pin

4. Upper pipe 5. Joint

Securelytightenthehexsocketheadbolttoxthejoint.

►Fig.11: 1. Joint 2. Hex socket head bolt

4. Cut the cable tie (nylon fastener), and remove it

from the tool.

►Fig.12: 1. Cable tie

Handle

1. Loosen the hex socket head bolt on the handle.

►Fig.13: 1. Hex socket head bolt 2. Handle

2. Set the angle and position of the handle as shown

inthegure,andthentightenthebolt.

►Fig.14: 1. Handle

Adjusting handle and hanger position

Loosen the hex socket head bolt on the handle. Move the

handle to a comfortable working position, and then tighten the bolt.

►Fig.15: 1. Hex socket head bolt 2. Handle

Loosen the hex socket head bolt on the hanger. Move the

hanger to a comfortable working position and then tighten the bolt.

►Fig.16: 1. Hanger 2. Hex socket head bolt

Installing the protector

WARNING: Never use the tool without the

guard illustrated in place. Failure to do so can

causeseriouspersonalinjury.

CAUTION: Take care not to injure yourself on

the cutter for cutting the nylon cord.

Attach the protector to the clamp using bolts.

►Fig.17: 1. Hex socket head bolt 2. Clamp

3. Protector 4. Cutter

Installing the cutting tool

CAUTION: Always use the supplied wrenches

to remove or to install the cutting tool.

CAUTION: Be sure to remove the hex wrench

inserted into the tool head after installing the

cutting tool.

NOTE:

The type of the cutting tool(s) supplied as the

standard accessory varies depending on the countries.

The cutting tool is not included in some countries.

NOTE: Turn the tool upside down so that you can

replace the cutting tool easily.

Nylon cutting head

NOTICE: Be sure to use genuine Makita nylon

cutting head.

1. Insert the hex wrench through the hole in the

motor housing to lock the spindle. Rotate the spindle

until the hex wrench is fully inserted.

►Fig.18: 1. Spindle 2. Motor housing 3. Hex wrench

NOTE: The holes in the motor housing are on the left

side and right side.

2. Place the nylon cutting head onto the spindle and

tighten it securely by hand.

►Fig.19:

1. Nylon cutting head 2. Spindle 3. Tighten 4. Loosen

3. Remove the hex wrench from the motor housing.

To remove the nylon cutting head, follow the installation

procedures in reverse.

Makita LXT BL 18 В, 460 Вт, D-рукоятка, d-30 см, M10xLH, разборвал (BL1830B DC18RC) DUR192LRF Инструкция по эксплуатации онлайн [18/52] 851294

Похожие устройства