Home
Главная
Stadler Form
Ультразвуковые
Eva WiFi white E-008
Инструкция по эксплуатации Страница: 8

Stadler Form Eva WiFi white E-008 Инструкция по эксплуатации онлайн [8/100] 854187

2. Take the Remote Sensor

(2), the stand (3) and the two batteries out of

the packaging. Open the battery compartment (4) on the underside of

the Remote Sensor

(2) by turning the lid anticlockwise. Insert the two

batteries into the battery compartment (4), as shown on page 4, and

close the lid again. Now place the Remote Sensor

(2) on the stand (3).

3. On the one hand, the Remote Sensor

(2) is a humidity sensor and

guarantees precise humidification by its external position. On the other

hand, the Remote Sensor

(2) also serves as a remote control. Position

the humidity sensor Remote Sensor

(2) in the centre of the room on a

table or a sideboard with an optimal distance from Eva between 3 – 5 m.

The Remote Sensor

should be positioned centrally in the room so that

the room air can flow past the sensor (5) as freely as possible. If this is

not possible, we recommend positioning the Remote Sensor

with a

minimum distance of 30 cm from the wall and a minimum distance of 2 m

from windows and ventilation openings.

4. Remove the water tank (6) by holding it by the handle and pulling it

up. Screw off the water tank lid (7) and fill the water tank with clean,

cold tap water up to the maximum mark. Make sure that the anticalc

cartridge (8) has been soaked in water for 24 hours prior (see “Before

setup“). Finally, screw the lid (7) back on the water tank (6). Then place

the water tank (6) in the unit. The water tray (9) will now slowly fill from

the water tank. Important: please do not move the appliance when it is

filled with water. The water could run into the electronics.

5. Press the on/off button (10) to switch Eva on. The current relative humid-

ity in % is shown on the display (15). If the water level indicator light (16)

is red, there is too little water in the unit. The humidification output level

is pre-set to level 3 and the desired humidity at 45 %.

6. Activate the Remote Sensor

(2) by pressing the “Hygrostat” button

(11a). The humidity sensor automatically sends information about the

measured relative humidity several times per minute to the unit, which

shows it on the display (15). The measurement can also be activated by

pressing any button on the Remote Sensor

(2) (aside from the on/off

button (10)).

7. The desired humidity can be changed by pressing the “Hygrostat” but-

ton (11) several times (30 – 75 % and continuous operation “CO”). The

symbol on the display (15) blinks during input. After a few seconds with-

out input, the selected value is saved. The symbol changes to the current

measured humidity.

Info: Once the desired air humidity is reached, the appliance stops and

the display blinks. Should the measured current air humidity fall below

the set value, the appliance begins to humidify again.

8. The humidification performance can be changed by pressing the “Out-

put” button (12) several times (levels 1 – 5). The level is indicated on the

display (15) by horizontal bars (e.g. 1 bar = level 1).

9. By pressing the “Warm” button (13), the warm mode, and with it the

water pre-heating, is turned on. Now the LED on the “Warm” button

on the unit is on. The heating plate (17) warms the water before it is

turned to mist by the ultrasonic membrane (19). The warm mode creates

a pleasantly warm mist plus increases the humidification performance.

10. By pressing the “Auto” button (14), the auto mode, and with it the Adap-

tive Humidity

Technology, is activated. Now the LED on the “Auto”

button on the unit is on. In auto mode, the unit adapts the humidification

Stadler Form Eva WiFi white E-008 Инструкция по эксплуатации онлайн [8/100] 854187

Похожие устройства