Home
Главная
DWT
Безударные
ABS-12 L-2 BMC 5.2.1
Инструкция по эксплуатации Страница: 26

DWT ABS-12 L-2 BMC 5.2.1 Инструкция по эксплуатации онлайн [26/164] 857108

English

Changing the rotational directions (see g. 9)

Change the direction of rotation only

after a full stop of the motor, acting oth-

erwise may cause damage to the power

tool.

Clockwise rotation (drilling, fastening of screws) -

move the reverse switch 8 to the left as it is shown in

g. 9.1.

Counter clockwise rotation (unscrewing the

screws) - move the reverse switch 8 to the right as it is

shown in g. 9.2.

Break rundown

Break rundown stops the keyless chuck 1 immediately

after the power tool is turned off� This helps to avoid

an excessive tightening of the bolts and screws and

prevents work pieces, screwdriver bits and slots of fas-

tening elements from being damaged�

Recommendations

on the power tool operation

Drilling (see g. 10-14)

• Grease the drill bit regularly when drilling holes in

metals (except drilling non-ferrous metals and their al-

loys)�

• When drilling hard metals, apply more force to the

power tool and lower the rotation speed�

• When drilling large diameter holes in metal, rst drill

a hole with a smaller diameter and ream it till the nec-

essary diameter (see g. 10).

• In order to avoid splitting of the surface at an exit

point of a drill bit when drilling holes in wood, follow the

instructions shown in gure 11.

• In order to decrease dust production when drilling

holes in walls and ceilings, take actions indicated in

gure 12-14.

Screwing the screws (see g. 15)

• To make fastening of screws easier and in order to

prevent cracking of the work pieces, rst drill a hole

with a diameter equal to 2/3 of a diameter of the screw�

• If you are connecting work pieces with the help of

screws, in order to achieve durable joint without get-

ting cracks, fracturing or layering, take actions shown

in gure 15.

Power tool maintenance /

preventive measures

Before execution of any procedures, centre the re-

verse switch 8.

Battery maintenance instruction

• Charge timely before the battery 2 is completely

exhausted� Stop operation in low power and charge

it immediately�

• Do not overcharge when the battery 2 is full, other-

wise it will shorten the life time�

• Charge battery 2 in the room temperature of 10°C

to 40°C (50°F to 104°F)�

• Charge battery 2 every 6 months without operation

for a long time�

• Replace worn out batteries in time� Decline of pro-

duction or a signicantly shorter runtime of the power

tool after charging indicates aging of the battery 2 and

the need for replacement� It should be taken into ac-

count that the battery 2 may discharge faster if the

works take place in the temperature below 0°С.

• In case of long time storage without use, it is recom-

mended to store the battery 2 at room temperature, it

should be charged to 50%�

Cleaning of the power tool

An indispensable condition for a safe long-term exploi-

tation of the power tool is to keep it clean� Regularly

ush the power tool with compressed air thought the

ventilation slots 9�

After-sales service and application service

Our after-sales service responds to your questions

concerning maintenance and repair of your product as

well as spare parts� Information about service centers,

parts diagrams and information about spare parts can

also be found under: www.dwt-pt.com�

•

Transportation

of the power tools

Categorically not to drop any mechanical impact on

the packaging during transport�

• When unloading / loading is not allowed to use any

kind of technology that works on the principle of clamp-

ing packaging�

Li-Ion batteries

The contained Li-Ion batteries are subject to the Danger-

ous Goods Legislation requirements� The user can trans-

port the batteries by road without further requirements�

When being transported by third parties (e�g�: air trans-

port or forwarding agency), special requirements on

packaging and labelling must be observed� For prepa-

ration of the item being shipped, consulting an expert

for hazardous material is required�

Dispatch batteries only when the housing is undam-

aged� Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move around

in the packaging� Please also observe possibly more

detailed national regulations�

Environmental

protection

Environmental

protection

Recycle raw materials instead of dispos-

ing as waste.

Power tool, accessories and packaging

should be sorted for environment-friendly

recycling�

The plastic components are labelled for categorized

recycling�

These instructions are printed on recycled paper man-

ufactured without chlorine�

The manufacturer reserves the possibility to introduce changes.

DWT ABS-12 L-2 BMC 5.2.1 Инструкция по эксплуатации онлайн [26/164] 857108

Содержание

Похожие устройства