Home
Главная
Worx
Циркулярные (дисковые)
WX437
Инструкция по эксплуатации Страница: 10

Worx WX437 Инструкция по эксплуатации онлайн [10/28] 861033

Compact Circular

Saw EN

Compact Circular Saw EN

I) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

m) Position the cord clear of the spinning

accessory. lf you lose control, the cord may be cut

or snagged and your hand or arm may be pulled into

the spinning wheel.

n) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning wheel may grab the surface and pull the

power tool out of your control.

o) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

p) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

q) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

r) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

s) Recommendation for the use of a residual

current device with a tripping current of 30 mA

or less.

FURTHER SAFETY

INSTRUCTIONS FOR

ABRASIVE CUTTINGOFF

OPERATIONS

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid

stalling of the rotating wheel which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the wheel’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-

up. The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in line with the

rotating wheel. Kickback will propel the tool in

direction opposite to the wheel’s movement at the

point of snagging.

d) Use special care when working Corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and

cause loss of control or kickback.

e) Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral

gap greater than 10 mm or toothed saw blade.

Such blades create frequent kickback and loss of

control.

f) Do not “jam” the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases

the loading and susceptibility to twisting or binding

of the wheel in the cut and the possibility of

kickback or wheel breakage.

g) When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless

until the wheel Comes to a complete stop.

Never attempt to remove the wheel from the

cut while the wheel is in motion otherwise

kickback may occur. lnvestigate and take

corrective action to eliminate the cause of wheel

binding.

h) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

the workpiece.

i ) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed under

the workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

j) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

ADDITIONAL SAFETY RULES

FOR YOUR CIRCULAR SAW

1. Only use saw blades recommended in the

Worx WX437 Инструкция по эксплуатации онлайн [10/28] 861033

Похожие устройства