Makita CXT UM600DWAE Инструкция к Makita UH201DWA онлайн [16/84] 862158
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita CXT UM600DWAE Инструкция к Makita UH201DWA онлайн [16/84] 862158

Makita CXT UM600DWAE Инструкция к Makita UH201DWA онлайн [16/84] 862158
16 ENGLISH
Installing or removing the shear
blades for grass shear
Removing the shear blades
1. Remove the grass receiver and place the tool
upside down.
►Fig.11
2. While pressing the lock lever, turn the undercover
counterclockwise until
on the undercover is aligned
with on the lock lever.
►Fig.12
3. Removetheundercover,shearblades,andcrank.
►Fig.13: 1.Undercover2.Shearblades3. Crank
Installing the shear blades
1. Preparethecrank,undercover,andnewshear
blades.
►Fig.14: 1. Crank 2.Undercover3.Shearblades
2. Removethebladecoverfromtheoldshear
blades,andthenattachittothenewones.
►Fig.15
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.16: 1.Alignmentline
4. Applyasmallamountofgreasetotheperiphery
ofthecrank.Attachthecranktothepinswiththesmall
andlargeroundsfacingup.
►Fig.17: 1. Crank
5.
Adjustthebladesandbaseplatesothattheholeinthe
baseplateandthetwoprotrusionsonthebladesarelinedup.
►Fig.18
6. Turntheshearbladesupsidedownandinstall
themsothatthepinsonthetooltintheholeonthe
baseplate.Makesurethattheshearbladesarexed
securely in place.
►Fig.19
7. Placetheundercoversothat
on the under-
cover is aligned with on the lock lever.
►Fig.20
8. While pressing the undercover, turn the under-
cover clockwise until
on the undercover is aligned
with on the lock lever.
►Fig.21
9. Makesurethatthelocklevertsinthegrooveon
the undercover.
►Fig.22: 1. Lock lever
CAUTION: Never use the tool without install-
ing the undercover.
10. Removethebladecover,andthenturnonthetool
to check that it works properly.
NOTICE: If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the shear
blades for hedge trimmer
CAUTION: Attach the blade cover before
removing or installing the shear blades.
Removing the shear blades
1. Placethetoolupsidedown.
►Fig.23
2. While pressing the lock lever, turn the undercover
counterclockwise until
on the undercover is aligned
with on the lock lever.
►Fig.24
3. Remove the undercover.
►Fig.25
4. Loosen the two screws with a screwdriver and
removetheshearblades.
►Fig.26: 1. Screws
NOTE:Theshearbladescanberemovedwithout
removing the screws.
5. Removethecrankfromtheshearblades.
►Fig.27: 1. Crank
NOTE:Thecrankmayremaininthetool.
Attachthebladecoverandthestoragecasetothe
removedshearblades,andthenstoretheblades.
Installing the shear blades
1. Preparethecrank,undercover,andnewshear
blades.
►Fig.28: 1. Crank 2.Undercover3.Shearblades
2. Attachthebladecovertotheshearblades.
►Fig.29
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.30: 1.Alignmentline
4. Applyasmallamountofgreasetotheperiphery
ofthecrank.Attachthecranktothepinswiththesmall
andlargeroundsfacingdown.
►Fig.31: 1. Crank
5. Slidetheshearbladessothattheholeonthe
baseplateispositionedatthecenteroftheringsofthe
blades.
►Fig.32
6.
Turntheshearbladesupsidedownandinstallthemso
thatthepinonthetooltsintheholeontheshearblades.
Inserttheclawofthebaseplateintothegrooveonthetool.
Makesurethattheshearbladesarexedsecurelyinplace.
►Fig.33: 1. Claw
7. Tightenthetwoscrewsrmlywithascrewdriver.
►Fig.34: 1. Screws
8. Placetheundercoversothat
on the under-
cover is aligned with on the lock lever.
►Fig.35

Похожие устройства

Скачать