Home
Главная
Worx
Аккумуляторные
40 В в коробке WG186E.92
Инструкция по эксплуатации Страница: 14

Worx 40 В в коробке WG186E.92 [14/28] Cordless grass line trimmer brushcutter attachment capable en

Cordless Grass Line Trimmer &

Brushcutter, Attachment-Capable

ASSEMBLY & OPERATION

NOTE: Before using the tool, read the

instruction book carefully.

Action Figure

Assembly

Assembling the Trimmer Shaft

Insert the screw into the hole, then

tighten the locking knob

See Fig. A

Assembling the Auxiliary Handle and

Safety-stop Handle

See Fig. B1,

Assembling the Safety Guard

Insert the metal bracket into the slot

on the safety guard, then secure the

guard in place using the screw and

hex key.

See Fig. C

Assembling the Shoulder Strap See Fig. D

Installing and Removing the Battery

Pack

NOTE:

• This machine will only run

when 2 batteries are installed. It

is recommended to use the same

two batteries and charge the

two batteries at the same time.

• When two batteries are used

with different amp hours or

charge level, the machine will

run to the lowest common

denominator.

* It is recommended that using

4.0Ah or above battery pack for

better performance and longer

run time.

See Fig.

E1, E2

Checking the battery charge

condition

NOTE: Fig. E3 only applies for the

battery pack with battery indicator

light.

See Fig. E3

Charging the battery pack

NOTE:

• The batteries are shipped

uncharged. Each battery must be

fully charged before the ﬁrst use.

• Always fully charge the two

batteries at same time. More details

can be found in charger’s manual.

See Fig. E4

Battery power indicator on the

machine

See details in BATTERY STATUS

section

See Fig. E5

Operation

To start

WARNING! The cutting head

continues to rotate after the

trimmer has been switched off; wait

until it has completely stopped then

lay down the tool.

Press the lock-off button ﬁrst, then

press the switch trigger to start the

machine.

See Fig. F

ECO Speed

For longer run time, press the ECO

button and switch trigger, then your

machine will operate at a low speed.

See Fig. G

Trimming See Fig. H

Bump feed See Fig. I

Assembling and removing the

trimmer head

Insert the hex key into the hole and

rotate the trimmer head until it stops

in a locked position. Then, rotate

counterclockwise to remove it, and

clockwise to assemble it.

See Fig. J

Winding the trimmer line

NOTE: The spool must be wound

while inside the trimmer head. The

spool cannot be wound with line,

then installed into the trimmer head.

See Fig. K

Assembling the brush cutter blade

Remove the trimmer head and the

skirt before assembling the brush

cutter blade.

Insert the hex key into the hole.

Place the brush-cutter blade on top

of the spacer, place washer on top of

the brush-cutter blade, place blade

housing over washer. After that, use

the wrench to tighten the lock-nut.

See Fig. L1,

L2, L3

Cutting See Fig. M

ATTACHMENT-CAPABLE ACCESSORIES

The below attachment accessories are sold

separately to convert the grass trimmer into a tool

for various applications.

1. Pole hedge trimmer attachment (WA0220)

This attachment is intended for cutting and

trimming hedges and bushes in domestic use.

2. Pole saw attachment (WA0222)

This attachment is intended for sawing of trees,

tree trunks, branches, limbs, etc. Cuts can be

sawed with or across the grain. This product is

not suitable for sawing mineral materials.

3. Edger attachment (WA0223)

This attachment is intended for edging around

walkways, driveways, ﬂower beds, etc.

Worx 40 В в коробке WG186E.92 [14/28] Cordless grass line trimmer brushcutter attachment capable en

Содержание

Похожие устройства