Home
Главная
Makita
Аккумуляторные
XGT BL TW007GD201
Инструкция к товару Страница: 10

Makita XGT BL TW007GD201 Инструкция к товару онлайн [10/40] 865191

10 ENGLISH

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

►Fig.2: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O󰀨 Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydi󰀨erslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Switch action

►Fig.3: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE: The tool automatically stops when you keep

pulling the switch trigger for 6 minutes.

NOTE: When full speed mode is turned on, the rota-

tion speed becomes fastest even if you do not pull the

switch trigger fully.

For detail information, refer to the section of full speed

mode.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.4: 1. Lamp

►Fig.5: 1. Button

To turn on the lamp status, press the button for

onesecond.Toturno󰀨thelampstatus,pressthebut-

ton for one second again.

With the lamp status ON, pull the switch trigger to turn

onthelamp.Toturno󰀨,releaseit.Thelampgoesout

approximately 10 seconds after releasing the switch

trigger.

With the lamp status OFF, the lamp does not turn on

even if pulling the trigger.

NOTE:Toconrmthelampstatus,pullthetrigger.

When the lamp lights up by pulling the switch trigger,

the lamp status is ON. When the lamp does not come

on, the lamp status is OFF.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoeso󰀨.In

this case, cool down the tool before operating again.

NOTE:Useadryclothtowipethedirto󰀨thelensof

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: While pulling the switch trigger, the lamp

status cannot be changed.

NOTE: For approximately 10 seconds after releasing

the switch trigger, the lamp status can be changed.

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Makita XGT BL TW007GD201 Инструкция к товару онлайн [10/40] 865191

Похожие устройства