Home
Главная
DWT
Универсальные
OF-1050 V 5.1.45
Инструкция по эксплуатации Страница: 24

DWT OF-1050 V 5.1.45 Инструкция по эксплуатации онлайн [24/176] 867609

English

used. Anytime when the milling cutter is used or

changed, it must be ensured that switch on the

machine is on off position� In order to avoid personal

injury done to you and your bystanders, the power

lines must be pulled out of the socket when the milling

cutter is assembled or changed�

• When the machine is used, you will work in

dusty environment; therefore, you should wear

mask and goggles. If you have long hair, you shall

wear hair care cap� You shall not wear loose clothes

during work�

• If the power lines are damaged, you shall not

touch them. It is prohibited to use any machine

with damaged power lines� The power lines must be

placed behind the frame (tool operation shall not be

affected)�

• The machine shall be operated in rain or humid

environment. You shall not touch the power lines to

avoid re or electric shock.

• Before the machine is removed from the

workpiece, you shall cut off power switch and

completely stop the milling cutter.

• The hands shall always be far away from the

rotating parts. When the milling cutter is in contact

with the workpiece, you shall not make an attempt to

start the machine�

• After work, the switch shall be turned off rst

and then lock knot of guide pillar shall be loosed

to make the machine return to original position.

Safety guidelines during

power tool operation

Before commencing operation

• During machining, do not place the workpiece on

a sturdy surface (concrete, steel, stone, etc�) - when

the router bit passes through the workpiece, you can

damage the router bit and lose control over the power

tool�

• Use the router bits whose allowable rotary speed

does not exceed the rotary speed of the power tool

spindle� Observe manufacturer's recommendations

for router bits use� Do not use router bits that do not

conform to the specications included in the user's

manual�

• Use only sharp nondefective router bits� Bended,

blunt or cracked router bits must be replaced�

• The router bit shank diameter must match precisely

with the internal diameter of the power tool collet�

• Never use the router bit if its cutting unit diameter

exceeds the diameter of the hole in the base plate�

• Remove all nails or any other metal objects from

blanks before cutting�

• When making cuts in walls or partitions, it is necessary

to nd the location of hidden wiring, water-pipes and

gas pipes� Severe injuries may occur as a result of

damaging electric wiring or household utility lines�

During operation

• When turning the power on and during operation,

hold the power tool with both hands by both handles

and keep a steady position, which will allow you to

keep control over the power tool�

• Keep your hands at a safe distance from the

rotating router bit� Remember that when machining a

workpiece, the router bit end occasionally protrudes

beyond the lower part of the workpiece and is not

protected - touching it may cause severe injuries�

Never touch the rotating router bit with your hands�

• Never start the machining until the router bit reaches

its full speed�

• Advance the router bit to the workpiece only with the

power tool turned on, otherwise the router bit may be

pinched in a workpiece, or a recoil and loss of control

over the power tool can occur�

• When processing small blanks, use clamping devic-

es. If the blanks are too small to be xed properly - do

not process them�

• Never remove sawdust while the power tool motor

is running�

• Do not work materials containing asbestos�

Asbestos is considered carcinogenic�

• Avoid stopping an electric tool motor when loaded�

• Avoid overheating your power tool, when using it for

a long time�

• Never operate the power tool over your head level�

After nishing operation

• The power tool may be removed from the workplace

only after it is turned off and the router bit stops

completely�

• Decelerating the router bit rotation by inertia using

the spindle keylock is strictly forbidden- this will put the

power tool out of operation and void your right to the

warranty service�

• During operation the router bit runs very hot - do not

touch it until it cools down�

• Cleaning of the workplace after work should be

performed by persons equipped with the aforesaid

personal protection means�

Warning: the chemical substances

contained in dust generated in sanding,

cutting, sawing, grinding, drilling and

other construction industry activities

may result in cancer, congenital deciency or be

harmful to the fertility. The ion of some chemical

substances shall be:

• Before any repair and replacement work to the

machine, the power plug must be pulled out rstly.

• The transparent two silicon oxide and other

masonry products in the wall bricks and cement;

the chromium arsenic (CCA) in wood with chemical

treatment� The harm degree of these substances shall

depend on the frequent degree of you carrying out

these works� If you want to reduce the contact with

these chemical substances, please work in the place

with ventilation and you shall use the appliances with

safety certicates (such as the dust mask designed

with tiny dust lter).

Notice the power voltage: in power connection, you

must conrm that if the power voltage is the same

to the voltage marked in the tool's data plate� If the

power voltage is higher than the appropriate voltage,

the accidents will be resulted to the operators, and at

the same time, the tool will be destroyed� Therefore, if

the power voltage has not been conrmed, then you

shall never plug in arbitrarily� On the contrary, when

the power voltage is lower than the required voltage,

the motor will be damaged�

DWT OF-1050 V 5.1.45 Инструкция по эксплуатации онлайн [24/176] 867609

Содержание

Похожие устройства