![Zalman VF2000 LED [5/9] Installation procedure usage as vga cooler](/img/pdf.png)
Zalman VF2000 LED [5/9] Installation procedure usage as vga cooler
![Zalman VF2000 LED [5/9] Installation procedure usage as vga cooler](/views2/1111031/page5/bg5.png)
4
Installation Procedure (Usage as VGA Cooler)
4. Spring Insertion on the Fixing Nut
Slowly turn the Spring in counter clockwise motion so that theSpring is correctly
attached to the Fixing Nut.
Note 1)
The ends of the Springs are of different diameters. Install the Spring end with the
smaller diameter on the Fixing Nut as shown in the diagram.
Note 2)
Make sure that the Spring is installed perpendicularly and not leaning to one
side.
1. VGA RAM Heatsink Attachment
Remove the film from the Thermal Tapes on the bottom
of the RAM Heatsinks and attach the Heatsinks on the
VGA RAM.
Note 1)
If Thermal Grease or other residue remains on the RAM,
then the Thermal Tapes will not stick. Clean the surface of
the RAM with acetone or alcohol before attaching the
RAM Heatsinks.
Note 2)
The bonding strength of the Thermal Tapes reaches 90%
after 24 hours of curing. Do not exert excessive force on
the RAM Heatsinks during this period.
Note 3)
Thermal Tapes are not reusable because they lose
adhesiveness after their initial application. Purchase new
Thermal Tapes if the RAM Heatsinks need to be
reattached.
※※
The following installation sequence MUST be followed.
(1. VGA RAM Heatsink Attachment
→ 2. Thermal Grease Application → 3. Nipple A Installation on Retention
Guide
→ 4. Spring Insertion on the Fixing Nut → 5. VGA Cooler Installation → 6. VGA Card Installation → 7. Fan
Power Cable Connection)
2. Thermal Grease Application
Clean the contact surface of the VGA Chipset completely.
Apply a thin and thorough layer of Thermal Grease on the
VGA Chipset that makes contact with the base of the
VGA Cooler.
3. Nipple A Installation on the Retention Guide
Install the short end of the Nipples A on the VGA Cooler’s
Retention Guide after determining the appropriate
Installation Holes.
(Note)
The Nipples MUST be tightened by hand. Using tools to
tighten the Nipples may damage the tips of the Nipples.
※ Cards with less than four installation holes, or with a diagonal
installation hole distance that is not 75.2mm are not compatible .
※ Please check the table below to identify the correct Nipple installation
Holes for specific models of VGA cards.
Section
Radeon HD 4870 Series
Radeon HD 4850 Series
Radeon HD 4830 Series
Radeon HD 3870 Series,
Radeon HD 3850 Series
Radeon HD 2600XT(DDR4) Series
Radeon X1950 Series
Radeon X1900 Series
Radeon X1800 Series
Geforce 9800GT Series
Geforce 9600GT, GSO Series
Geforce 9500GT, 9400GT Series
Geforce 8800GT, GS, GTS(G92) Series
Geforce 8600GT, 8500GT Series
Geforce 7950 Series(except GX2)
Geforce 7900, 7800, 7600 Series
Geforce 6800, 6600 Series
(except 6600 AGP Series)
Quadro FX Series
(except 4600, 4700X2, 5600 Series)
NVIDIA
Compatible
VGA cards
AMD(ATI)
Содержание
- Cautions on use and installation 2
- Components 2
- Specifications 2
- Amd ati 5
- Compatible vga cards 5
- Installation procedure usage as vga cooler 5
- Nvidia 5
- Section 5
- Connect the appropriate 3 pin connector on the cable to the motherboard fan header and the vf2000 led fan connector 6
- Pcie or agp slot use the fixing bolt to secure the vga card onto the computer case if the vga card has a power connector on it then remember to plug in the power cable 6
- Pull the 6 pin connector out of the system through the back and connect it to fan mate 2 which should be installed on the case using the included double sided tape ⑧ 6
- Vga card installation insert the assembled vga card into the motherboar 6
- Installation procedure usage as cpu cooler 7
- Removal of motherboard from case please remove the motherboard from the case to allow proper installation of the vf2000 2 removal of pre installed coolers and installation hardware please remove any pre installed coolers and all related hardware components from the motherboard note in the case of the amd am2 am2 motherboards the stock retention frame must be removed 3 thermal grease application clean the contact surface of the cpu completely apply a thin and thorough layer of thermal grease on the cpu that makes contact with the base of the vf2000 7
Похожие устройства
- Philips 48PFS8109/60 Инструкция по эксплуатации
- Zalman VF950 LED Инструкция по эксплуатации
- Philips 55PFS8109/60 Инструкция по эксплуатации
- Zalman CNPS7000C-Cu Инструкция по эксплуатации
- Texet T-55 Beige Инструкция по эксплуатации
- Zalman Z-Machine GV1000 Инструкция по эксплуатации
- Lenovo TAB A8-50 8" 16Gb 3G Red (A5500) Инструкция по эксплуатации
- Zalman CNPS9500A LED Инструкция по эксплуатации
- Lenovo TAB A8-50 8" 16Gb 3G Yellow (A5500) Инструкция по эксплуатации
- Zalman VF1000 LED Инструкция по эксплуатации
- Alienware A18-9288 Инструкция по эксплуатации
- Zalman CNPS7500-Cu LED Инструкция по эксплуатации
- Lenovo IdeaPad Yoga 2-13 /59422681/ Инструкция по эксплуатации
- Zalman CNPS7500-AlCu LED Инструкция по эксплуатации
- Samsung S27D590CS Инструкция по эксплуатации
- Zalman CNPS9700 LED Инструкция по эксплуатации
- Lenovo IdeaCentre B550 /57326702/ Инструкция по эксплуатации
- Zalman CNPS9500 AT Инструкция по эксплуатации
- Lenovo IdeaCentre C560 /57326466/ Инструкция по эксплуатации
- Zalman VNF100 Инструкция по эксплуатации