Bort Alligator MEGA 93417425 Инструкция к BORT Alligator MEGA 93417425 онлайн [12/48] 871944

Bort Alligator MEGA 93417425 Инструкция к BORT Alligator MEGA 93417425 онлайн [12/48] 871944
12
for leaks.
5. Insert the noise absorbing screen into the drain hole
at side up. (Fig.8.3)
8. CONNECTING THE OUTLET PIPE
To the DRAIN PIPE ATTENTION!
It is recommended to wear protective goggles when
installing the disposer.
For all models, the drain pipe is connected using a
screw connection (Fig. 9.2). First connect the hydrau-
lic lock to the disposer and then to the drain. For the
connection a siphon with smooth walls should be
used.
Use a sanitary sealant only for connecting the ange
of the sink with the disposer.
Do not use sealants for threaded pipe connections or
anaerobic screwed sealants. They can damage the
product.
Regularly check the disposer and ttings for water
leaks, since leaks water can cause damage to prop-
erty.
The manufacturer is not responsible for damage to
property as a result of water leaks.
INSTALLING THE DRAINAGE SYSTEM
1. Put the ange (2) on the drain pipe Insert the rubber
seal (1). Fasten drain tube, tightly pulling it to the body
disposer with screws (4). (Fig. 9.1)
9. CONNECTING THE DISPOSER TO THE ELECTRICAL
NETWORK
ATTENTION! ELECTRIC SHOCK CURRENT
To prevent electric shock, turn off the power before in-
stalling or servicing the product.
If you are not qualied enough, call an electrician to
connect the product to the power.
If a three–pin grounding–type plug is used to connect a
three–contact outlet with ground.
Do not modify the design of the plug supplied with the
device.
Improper equipment grounding may cause electric
shock current.
All electrical connections must comply with the electri-
cal and norms.
Do not connect the ground to the feed pipe gas.
Do not power on the distribution shield until you have
installed the sockets with proper grounding.
If the power cord is damaged, it must be replaced at the
service center.
NOTE: Access to a grounded outlet is required. In-
stalling all additional outlets must be carried out by a
qualied electrician, and all outlets must be properly
grounded.
Turn ON/OFF device
Depending on the models BORT disposer are equipped
with two types of control: a wireless (wall) switch or a
pneumatic switch.
Wireless (wall) switch
The disposer of the “Control and FullControl” series are
equipped with a wireless wall mount switch.
The switch should be located in a convenient (safe for
children) place above the table top.
For instal the switch to the wall, use double–sided tape.
For activate / deactivate the device, hold down the key
for 2–3 seconds.
Battery type: Voltage: 12V; Size: A27
Air switch
Disposer is equipped with an air switch and a connect-
ing pipe (except “Control” series).
INSTALLATION OF AIR SWITCH
1. Drill a hole with a diameter of 32 mm in suitable top
or top the panel of a sink. Some sinks may already have
a suitable A hole for the opening of which is necessary
remove the cover.
2. Unscrew the nut from the body of the push button,
while holding the stainless steel washer and rubber
gasket in place. Place one end of the PVC tube on the
spout on the body Press the other end to A hole in the
table top and a nut located under the countertop. (Fig.
10.2)
3. Place the push button housing in the hole and tighten
the nut underneath countertop (enough arm effort). Do
not use the key to tighten nut. (Fig. 10.3)
4. Take the other end of the duct and tightly put it on
the spout of the air switch located on the bottom of
the disposer. (Fig.10.4) Hand tighten the clamping nut.
The disposer installation is complete. Before using the
product, read all of the instructions. operation and safe-
ty contained in paragraph 10 of this manual. In conclu-
sion, install the plug in the sink in the Closed position.
Fill the sink with water, Remove the plug and check the
connections on the a water leakage.
10. ATTENTION! IMPORTANT INSTRUCTIONS FOR
SAFETY
If the air switch does not work, remove the plug power

Похожие устройства

Скачать