Vitek VT-1364 Руководство по эксплуатации онлайн [10/24] 147582
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1364 Руководство по эксплуатации онлайн [10/24] 147582

Vitek VT-1364 Руководство по эксплуатации онлайн [10/24] 147582
10
ENGLISH
HAIRCUTTING
– Hair should be clean and dry during hair-
cutting. The best results of haircutting are
attained if the hair is dry, not wet.
– Seat the person so that his/her head is
approximately at your eye level, cover the
person’s shoulders with a towel and set hair
with the comb.
– Always start cutting from the back of the head.
– You can cut hair against and along the direc-
tion of hair growth, but keep in mind that the
hair cut against the growth will be shorter than
the hair cut along the growth.
– To leave longer hair, take hair locks between
your fingers and cut it using the hair clipper.
– Always cut off little amount of hair at a time;
you can always return to the cut area again for
additional cutting.
– In the shaver on mode, you can press the
«Turbo» button «Т» (5) to increase the power
of the shaver, this mode can be used depend-
ing on the situation. The «Turbo» mode indi-
cator (9) will glow red while the «Turbo»
button «Т» (5) is pressed.
– Comb the hair to reveal uneven locks.
– You can lift the hair locks and cut them along
the comb (19).
– Use scissors to trim hair.
– With time you will learn to model desired hair-
cuts by yourself.
STYLING
Step one
Set the «3 mm» attachment comb (11) or «6 mm»
attachment (12). Switch the unit on by using the
power switch (6) « ». Hold the unit with the
blades pointed upwards. Start cutting from the
hair growth edge. Slowly move the unit upwards.
Cut the back of the head area at the bottom and
near the ears.
Step two
Switch the unit off by using the power switch (6)
« » a second time. Set the «9 mm» attachment
comb (13) or «12 mm» attachment (14). Switch
the unit on and continue cutting hair near the
crown of the head.
Step 3 – cutting in the temples area
Switch the unit off, set the «3 mm» attachment
comb (11) or «6 mm» attachment (12). Cut the
hair on the temples. Then use the «9 mm» attach-
ment (13) or «12 mm» attachment (14) and con-
tinue cutting towards the top of the head.
Step 4 – cutting the top of the head
Using the «9 mm» attachment (13) or «12 mm»
attachment (14), cut the hair on the top of the
head towards the crown against the hair growth
direction.
Step 5 – the final part
Remove the attachment from the unit, turn the
blades of the unit towards the hair and carefully
trim hair on the temples and neck. Do not press
on the unit; there is danger of injuries or cuts
when open blades come in contact with the skin.
Cone-shaped haircut
Install the necessary attachment (11-14) and start
cutting from the head back towards the crown. Cut
hair against hair growth from the head front to the
top of the head and on the sides. To get a flat top
haircut, use the comb: lift the locks and cut them
along the comb. Comb the hair to reveal uneven
locks.
CLEANING AND MAINTENANCE
– Switch the unit off after use.
– Remove the attachment (
11-14
) from the unit
body and clean the inside and outside of the
attachments (
11-14
) from the cut hair, using
the cleaning brush (17) (pic.2).
– You can wash the attachments (
11-14
) under a
water jet, then wipe them and dry out.
– Wipe the unit body with a soft slightly damp
cloth. Do not immerse the hair clipper body,
power cord and power plug into water or other
liquids.
– Never use solvents or abrasives to clean the
unit body and attachments.
Blade block
Caution! Do not wash the blade block with
water; use lab alcohol to wash the blade block.
Regularly lubricate the trimmer blades (1) using
the oil (18) supplied with the unit (pic. 3).
– Switch the hair clipper off with the button (6)
“ ”, unplug it if the unit is being charged.
– Remove the attachment (11-14).
– Remove the trimmer block (1) by pressing the
button 3 (pic. 1).

Похожие устройства

Скачать