Home
Главная
Bort
Измельчитель пищевых отходов
TITAN 5000 (Control)
Руководство по эксплуатации Страница: 12

Bort TITAN 5000 (Control) Руководство по эксплуатации онлайн [12/48] 511343

in the horizontal part of the drainage pipes,

moving with side of the siphon towards the main

pipe.

IF THE DISHWASHER WILL NOT BE CONNECTED

TO THE DISPOSER, GO TO PART 7 OF THIS

INSTRUCTION

6. CONNECTING THE DISHWASHER

MACHINES AND TRANSFER CONNECTION

To connect the dishwasher, you should use the

input hole in the top of the disposer (Fig. 7.2).

To connect, remove the barrier (Fig. 7.1).

If the sink is overlled with liquid, then it should

be connected through the inlet in its upper part

of the drain pipe (Fig. 7.2).

!!! On some models, there is

a barrier inside the drain pipe

parent to be removed.

REMOVING THE PLATE / PARTITION

1. Place the disposer on one side and place

it screwdriver into the connection for the

dishwasher, pushing it until it will not rest against

the partition in the end of the branch pipe.

2. With several blows of the hammer, knock out

the septum in the branch pipe (Fig. 7.1).

3. Remove the embossed partition from the

disposer bowl. If necessary to connect the

dishwasher, then it should be connected to the

inlet of the overow outlet pipes To connect to

the overow inlet, remove the exhaust pipe cover

by unscrewing the cover (Fig. 7.3).

7. CONNECTING THE DISPOSER TO THE FIXING

UNIT ATTENTION!

To avoid injury, follow the so that during the

removal and installation of a part Your body was

not under the disposer; during the installation it

is possible to drop it.

Remove any objects from the grinding chamber

product before installing it on the sink.

1. Install the product in such a way that provide

easy access to the restart button engine located

in the lower part of the body. Do not block this

place with any objects.

2. Place the disposer with three mounting loops

(1) into the sliding position by mounting rails (2).

(Fig.8.1)

3. Lift the disposer, insert the top end (installation

gasket) in the mounting and turn the setting

ring to the right (with a wrench or adjustable

pliers) until the mounting loops are xed (3) with

respect to the mounting rails (Fig. 8.2).

Make sure that all three mounting loops are

locked. Disposer is installed.

4. Run water into the sink, then check the

connections for leaks.

5. Insert the noise absorbing screen into the

drain hole at side up. (Fig.8.3)

8. CONNECTING THE OUTLET PIPE

To the DRAIN PIPE ATTENTION!

• It is recommended to wear protective goggles

when installing the disposer.

• For all models, the drain pipe is connected

using a screw connection (Fig. 9.1).

• Use a sanitary sealant only for connecting the

ange of the sink with the disposer.

Do not use sealants for threaded pipe

connections or anaerobic screwed sealants.

They can damage the product.

• Regularly check the disposer and ttings

for water leaks, since leaks water can cause

damage to property.

The manufacturer is not responsible for damage

to property as a result of water leaks.

INSTALLING THE DRAINAGE SYSTEM

1. Put the ange (2) on the drain pipe Insert the

rubber seal (1). Fasten drain tube, tightly pulling

it to the body disposer with screws (4). (Fig. 9.1)

9. CONNECTING THE DISPOSER TO THE ELEC-

TRICAL NETWORK

ATTENTION! ELECTRIC SHOCK CURRENT

• To prevent electric shock, turn off the power

before installing or servicing the product.

• If you are not qualied enough, call an

electrician to connect the product to the power.

• If a three-pin grounding-type plug is used to

connect a three-contact outlet with ground.

• Do not modify the design of the plug supplied

with the device.

• Improper equipment grounding may cause

electric shock current.

• All electrical connections must comply with the

electrical and norms.

• Do not connect the ground to the feed pipe gas.

• Do not power on the distribution shield until

you have installed the sockets with proper

grounding.

• If the power cord is damaged, it must be

replaced at the service center.

NOTE: Access to a grounded outlet is required.

Installing all additional outlets must be carried

out by a qualied electrician, and all outlets must

be properly grounded.

Turn ON/OFF device

Depending on the models BORT disposer are

equipped with two types of control: a wireless

Bort TITAN 5000 (Control) Руководство по эксплуатации онлайн [12/48] 511343

Похожие устройства