![Gigabyte GA-H55M-S2H (REV. 1.0) — настройки BIOS: Управление встроенными компонентами и портами [49/96]](/icons/site-icon-64.png){kind=icon}
Gigabyte GA-H55M-S2H (REV. 1.0) — настройки BIOS: Управление встроенными компонентами и портами [49/96]
Превью страниц
Страница 49 /
96
![Gigabyte GA-H55M-S2H (REV. 1.0) [49/96] Onboard ide controller jmicron jmb368 chip](/views2/1115297/page49/bg31.png)
- 49 - BIOS Setup
Onboard LAN Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
Onboard IDE Controller (JMicron JMB368 Chip)
Enables or disables the IDE controller integrated in the JMicron JMB368 chip. (Default: Enabled)
Onboard Serial Port 1
Enables or disables the rst serial port and species its base I/O address and corresponding interrupt.
Options are: Auto, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled.
When a Cable Problem Occurs...
If a cable problem occurs on a specied pair of wires, the Status eld will show Short and then length
shown will be the approximate distance to the fault or short.
Example:
Part1-2 Status = Short / Length = 2m
Explanation: A fault or short might occur at about 2m on Part 1-2.
Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Status elds will show
Open, and the length shown is the approximate length of the attached LAN cable.
Содержание
478- Ga h55m s2h
- User s manual
- Motherboard
- Ga h55m s2h
- Dec 7 2009
- Copyright
- Information in this manual is protected by copyright laws and is the property of gigabyte changes to the specifications and features in this manual may be made by gigabyte with out prior notice no part of this manual may be reproduced copied translated transmitted or published in any form or by any means without gigabyte s prior written permission
- Documentation classifications
- Disclaimer
- 2009 giga byte technology co ltd all rights reserved the trademarks mentioned in this manual are legally registered to their respective owners
- The revision number on your motherboard looks like this rev x x for example rev 1 means the revision of the motherboard is 1 check your motherboard revision before updating motherboard bios drivers or when looking for technical information
- In order to assist in the use of this product gigabyte provides the following types of documentations
- Identifying your motherboard revision
- For product related information check on our website at http www gigabyte com tw
- Example
- Chapter 2 bios setup 1
- Table of contents
- Chapter 1 hardware installation
- Box contents optional items ga h55m s2h motherboard layout block diagram
- Chapter 5 appendix 7
- Chapter 4 unique features 1
- Chapter 3 drivers installation 7
- Optional items
- Box contents
- Ga h55m s2h
- Ga h55m s2h motherboard layout
- Block diagram
- Chapter 1 hardware installation
- 1 installation precautions
- 2 product specifications
- 3 installing the cpu and cpu cooler
- 3 1 installing the cpu
- 3 2 installing the cpu cooler
- 4 1 dual channel memory configuration
- 4 installing the memory
- 4 2 installing a memory
- 5 installing an expansion card
- 6 back panel connectors
- Hdmi port
- Dvi d port
- D sub port
- Usb port
- Ps 2 keyboard mouse port
- Line out jack green
- Side speaker out jack gray
- Rj 45 lan port
- Rear speaker out jack black
- Optical s pdif out connector
- Mic in jack pink
- Line in jack blue
- Dual display configurations for the onboard graphics
- Center subwoofer speaker out jack orange
- 7 internal connectors
- The main power connector is compatible with power supplies with 2x10 power connectors
- High power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- 22 hardware installation
- 2 atx_12v atx 2x2 12v power connector and 2x12 main power connector
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- When using a 2x12 power supply remove the protective cover from the main power connector on the motherboard do not insert the power supply cable into pins under the protective cover when using a 2x10 power supply
- To meet expansion requirements it is recommended that a power supply that can withstand
- The motherboard has a 4 pin cpu fan header cpu_fan and a 4 pin system fan header sys_fan most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the motherboard supports cpu fan speed control which requires the use of a cpu fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- This connector is used to connect a floppy disk drive the types of floppy disk drives supported are 360 kb 720 kb 1 mb 1 4 mb and 2 8 mb before connecting a floppy disk drive be sure to locate pin 1 of the connector and the floppy disk drive cable the pin 1 of the cable is typically designated by a stripe of different color for purchasing the optional floppy disk drive cable please contact the local dealer
- These fan headers are not configuration jumper blocks do not place a jumper cap on the
- Heating overheating may result in damage to the cpu or the system may hang
- Headers
- Fdd floppy disk drive connector
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from over
- 4 cpu_fan sys_fan fan headers
- 23 hardware installation
- The ide connector supports up to two ide devices such as hard drives and optical drives before attach ing the ide cable locate the foolproof groove on the connector if you wish to connect two ide devices remember to set the jumpers and the cabling according to the role of the ide devices for example master or slave for information about configuring master slave settings for the ide devices read the instructions from the device manufacturers
- Sata2_0 1 2 3 4 5 sata 3gb s connectors controlled by h55 chipset
- Ide ide connector
- 24 hardware installation
- The sata connectors conform to sata 3gb s standard and are compatible with sata 1 gb s standard each sata connector supports a single sata device
- Bat battery
- F_panel front panel header
- You may connect the audio cable that came with your optical drive to the header
- The front panel audio header supports intel high definition audio hd and ac 97 audio you may connect your chassis front panel audio module to this header make sure the wire assignments of the module con nector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- The front panel audio header supports hd audio by default if your chassis provides an ac 97
- Some chassis provide a front panel audio module that has separated connectors on each wire
- Ously if you want to mute the back panel audio only supported when using an hd front panel audio module refer to chapter 5 configuring 2 4 5 7 channel audio
- Instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- Front panel audio module refer to the instructions on how to activate ac 97 functionality via the audio software in chapter 5 configuring 2 4 5 7 channel audio
- F_audio front panel audio header
- Cd_in cd in connector
- Audio signals will be present on both of the front and back panel audio connections simultane
- 27 hardware installation
- Spdif_o s pdif out header
- Spdif_i s pdif in header
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- The coma header can provide one serial port via an optional com port cable for purchasing the op tional com port cable please contact the local dealer
- F_usb1 f_usb2 usb headers
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb header prior to installing the usb bracket be sure to turn off your computer and unplug the power
- Cord from the power outlet to prevent damage to the usb bracket
- Coma serial port header
- 29 hardware installation
- Phase led
- Clr_cmos clearing cmos jumper
- Chapter 2 bios setup
- 1 startup screen
- Sample bios version e2
- Bios setup program function keys
- 2 the main menu
- Exit without saving
- Advanced bios features
- Standard cmos features
- Set user password
- Set supervisor password
- Save exit setup
- Power management setup
- Pc health status
- Mb intelligent tweaker m i t
- Load optimized defaults
- Load fail safe defaults
- Keys for the main menu only
- Integrated peripherals
- Note this item appears only if you install a memory module that supports this feature
- M i t current status
- Advanced frequency settings
- 35 bios setup
- 3 mb intelligent tweaker m i t
- Whether the system will work stably with the overclock overvoltage settings you made is dependent on your overall system configurations incorrectly doing overclock overvoltage may result in dam age to cpu chipset or memory and reduce the useful life of these components this page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results inadequately altering the settings may result in system s failure to boot if this occurs clear the cmos values and reset the board to default values
- This screen provides information on cpu memory frequencies parameters
- Cpu multi threadin
- Cpu frequency
- Cpu enhanced halt c1e
- Cpu cores enable
- Cpu clock ratio
- C3 c6 c7 state suppor
- Bios setup 36
- Being installed being installed
- Allows you to determine whether to let the cpu enter c3 c6 c7 mode in system halt state when en abled the cpu core frequency and voltage will be reduced during system halt state to decrease power consumption the c3 c6 c7 state is a more enhanced power saving state than c1 auto lets the bios automatically configure this setting default auto
- Note this item is present only if you install a cpu that supports this feature for more information about
- Allows you to determine whether to enable multi threading technology when using an intel cpu that supports this function this feature only works for operating systems that support multi processor mode default enabled
- Intel cpus unique features please visit intel s website intel cpus unique features please visit intel s website
- Allows you to determine whether to enable all cpu cores
- Enables or disables intel cpu enhanced halt c1e function a cpu power saving function in system halt state when enabled the cpu core frequency and voltage will be reduced during system halt state to decrease power consumption auto lets the bios automatically configure this setting default auto
- Allows you to alter the clock ratio for the installed cpu the adjustable range is dependent on the cpu
- Enables only two cpu cores
- All all enables all cpu cores default
- Enables only three cpu cores
- Advanced cpu core features
- Enables only one cpu core
- Displays the current operating cpu frequency
- Qpi link speed
- Qpi clock ratio
- Extreme memory profile x m p
- Cpu thermal monito
- Cpu eist functio
- Bi directional procho
- Bclk frequency mhz
- Base clock bclk control
- Extreme memory profile x m p
- Options are 700mv 800mv default 900mv 1000mv options are 700mv 800mv default 900mv 1000mv
- Advanced clock control
- Options are 700mv 800mv 900mv default 1000mv options are 700mv 800mv 900mv default 1000mv
- Options are 0ps 750ps default 0ps options are 0ps 750ps default 0ps
- Note this item appears only if you install a memory module that supports this feature
- Memory frequency mhz
- Frequency mhz frequency mhz
- Cpu clock skew
- Cpu clock drive
- Bios setup 38
- Allows you to set the system memory multiplier auto sets memory multiplier according to memory spd data default auto
- The settings under the three items above are synchronous to those under the same items on the mb intelligent tweaker m i t main menu
- Allows you to set the cpu clock prior to the chipset clock
- The first memory frequency value is the normal operating frequency of the memory being used the second is the memory frequency that is automatically adjusted according to the bclk frequency mhz and system memory multiplier settings
- Allows you to manually set the pcie clock frequency the adjustable range is from 90 mhz to 150 mhz auto sets the pcie clock frequency to standard 100 mhz default auto
- System memory multiplier spd memory
- System memory multiplier spd
- Allows you to adjust the amplitude of the pci express and chipset clock
- Pci express frequency mhz
- Allows you to adjust the amplitude of the cpu and the chipset clock
- Pci express clock drive
- Advanced memory settings
- Options are auto default 1 31
- Options are auto default 1 15
- Extreme extreme lets the system operate at its best performance level
- Dram timing selectable spd
- Channel a b timing settings
- Channel a b standard timing control
- Channel a b advanced timing control
- When using a non xmp memory module or extreme memory profile x m p is set to disabled this item will display as 1 v when extreme memory profile x m p is set to profile1 or profile2 this item will display the value based on the spd data on the xmp memory
- Cas latency time
- Turbo turbo lets the system operate at its good performance level default
- The value displayed here is dependent on the cpu being used
- Allows the system to operate at three different performance levels
- Standard standard lets the system operate at its basic performance level
- 39 bios setup
- Quick and expert allows the memory timing settings below to be configurable options are auto default quick expert
- Profile qpi voltage
- Profile ddr voltage
- Performance enhance
- Options are auto default 6 15
- Options are auto default 1 63
- Load line calibration
- Enables or disables load line calibration enabling this feature adjusts vdroop keeping the cpu voltage more constant under light and heavy cpu load disabled sets the cpu voltage following intel specifications default disabled note enabling load line calibration may result in damage to your cpu or reduce the useful life of the cpu
- Command rate cmd
- Channel a b misc timing control
- Bios setup 40
- Advanced voltage settings
- Static trd
- Options are auto default 1 7
- Options are auto default 1 63
- Options are auto default 1 31
- Options are auto default 1 3
- Options are auto default 1 255
- Options are auto default 1 15
- Options are auto default 1 10
- Dram termination
- Cpu vcore
- Cpu vaxg voltage
- Cpu pll
- Ch b data vref
- Ch b address vref
- Ch a data vref
- Ch a address vref
- Qpi vtt voltage
- Pch core
- Dynamic vcore dvid
- Dram voltage
- Virtualization technolog
- This section provides information on the bios version cpu base clock cpu frequency memory frequency total memory size cpu temperature chipset temperature vcore and memory voltage
- Note this item is present only if you install a cpu that supports this feature for more information about
- Miscellaneous settings
- Isochronous support
- Intel cpus unique features please visit intel s website intel cpus unique features please visit intel s website
- Enables or disables intel virtualization technology virtualization enhanced by intel virtualization tech nology will allow a platform to run multiple operating systems and applications in independent partitions with virtualization one computer system can function as multiple virtual systems default enabled
- Determines whether to enable specific streams within the cpu and chipset default enabled
- Bios setup 42
- Sets the system time for example 1 p m is 13 0 0 select the desired field and use the up arrow or down arrow key to set the time
- Access mode access mode sets the hard drive access mode options are auto default chs lba large
- Sets the system date the date format is week read only month date and year select the desired field and use the up arrow or down arrow key to set the date
- 43 bios setup
- None if no ide sata devices are used set this item to none so the system will skip
- 4 standard cmos features
- Manual allows you to manually enter the specifications of the hard drive when the hard
- Ide hdd auto detection
- Ide channel 2 3 master 4 master slave
- Ide channel 0 1 master slave ide channel 0 1 master slave
- Ide channel 0 1 master slave
- Ide auto detection
- Extended ide drive extended ide drive
- Drive access mode is set to drive access mode is set to chs
- Date mm dd yy
- Configure your ide sata devices by using one of the two methods below configure your ide sata devices by using one of the two methods below
- To autodetect the parameters of the ide sata device on this channel
- Configure your ide sata devices by using one of the three methods below configure your ide sata devices by using one of the three methods below
- Time hh mm ss
- Auto lets the bios automatically detect ide sata devices during the post default
- The detection of the device during the post for faster system startup the detection of the device during the post for faster system startup
- Access mode access mode sets the hard drive access mode options are auto default large
- Memory
- Halt on
- Drive a
- Password check
- Note this item is present only if you install a cpu that supports this feature for more information about intel cpus unique features please visit intel s website
- Here synchronize with the settings of the smart quickboot of smart 6 default disabled here synchronize with the settings of the smart quickboot of smart 6 default disabled
- Hdd s m a r t capability
- Hard disk boot priority
- First second third boot device
- Enables or disables the s m a r t self monitoring and reporting technology capability of your hard drive this feature allows your system to report read write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed default disabled
- Enables or disables the quick boot function to speed up the system boot up process to shorten the wait ing time for entering the operating system and to deliver greater efficiency for daily use the settings
- 5 advanced bios features
- To exit this menu when finished
- 45 bios setup
- To accept options are floppy ls120 hard disk cdrom zip usb fdd usb zip usb cdrom usb hdd legacy lan disabled
- System system a password is required for booting the system and for entering the bios setup
- Specifies whether a password is required every time the system boots or only when you enter bios setup after configuring this item set the password s under the set supervisor user password item in the bios main menu
- Setup setup a password is only required for entering the bios setup program default
- Quick boot
- Program program
- Onboard vga
- On chip frame buffer size
- No execute memory protec
- Limit cpuid max to
- Init display first
- Delay for hdd secs
- Backup bios image to hdd
- Sata port0 3 native mode intel h55 chipset
- 6 integrated peripherals
- Sata controllers use dedicated irqs that cannot be shared with other device set sata controllers use dedicated irqs that cannot be shared with other device set
- 47 bios setup
- Sata ahci mode intel h55 chipset
- Native mode native mode
- Mode mode
- If you wish to install operating systems that support native mode default if you wish to install operating systems that support native mode default
- Ide ide configures the sata controller to ide mode default
- Enables or disables the integrated usb controllers default enabled
- Enabled enabled allows the sata controllers to operate in native ide mode enable native ide mode
- Disabled disabled will turn off all of the usb functionalities below
- Disabled disabled allows the sata controllers to operate in legacy ide mode in legacy mode the
- Usb storage function
- Determines whether to detect usb storage devices including usb flash drives and usb hard drives during the post default enabled
- Usb legacy function
- Allows you to decide whether to configure the sata controller integrated in the intel h55 chipset to ahci
- Usb controllers
- This option to this option to disabled if you wish to install operating systems that do not support
- Allows usb keyboard to be used in ms dos default enabled
- Specifies the operating mode of the integrated sata controllers
- Ahci is an interface specification that allows the storage driver to enable advanced ahci is an interface specification that allows the storage driver to enable advanced
- Serial ata features such as native command queuing and hot plug serial ata features such as native command queuing and hot plug
- Ahci ahci configures the sata controller to ahci mode advanced host controller interface
- Smart lan
- Onboard h w lan
- Green lan
- Azalia codec
- Onboard serial port 1
- Onboard lan boot rom
- Onboard ide controller jmicron jmb368 chip
- S1 pos s1 pos enables the system to enter the acpi s1 power on suspend sleep state
- Allows the system to be awakened from an acpi sleep state by a wake up signal from a modem that supports wake up function default enabled
- Resume by alarm
- Acpi suspend type
- 7 power management setup
- Power on by ring
- Pme event wake up
- Note supported on windows 7 vista operating system only
- Its working state exactly where it was left off its working state exactly where it was left off
- Instant off instant off press the power button and then the system will be turned off instantly default
- In s3 sleep state the system appears to be off and consumes less power than in in s3 sleep state the system appears to be off and consumes less power than in
- In s1 sleep state the system appears suspended and stays in a low power mode in s1 sleep state the system appears suspended and stays in a low power mode
- If enabled set the date and time as following if enabled set the date and time as following
- Determines whether to power on the system at a desired time default disabled
- The system can be resumed at any time the system can be resumed at any time
- Delay 4 sec delay 4 sec press and hold the power button for 4 seconds to turn off the system if the power
- The s1 state when signaled by a wake up device or event the system resumes to the s1 state when signaled by a wake up device or event the system resumes to
- Configures the way to turn off the computer in ms dos mode using the power button
- Specifies the acpi sleep state when the system enters suspend
- Button is pressed for less than 4 seconds the system will enter suspend mode button is pressed for less than 4 seconds the system will enter suspend mode
- Soft off by pwr bttn
- Bios setup 50
- S3 str s3 str enables the system to enter the acpi s3 suspend to ram sleep state default
- Allows the system to be awakened from an acpi sleep state by a wake up signal from a pci or pcie de vice note to use this function you need an atx power supply providing at least 1a on the 5vsb lead default enabled
- Power on by mouse
- Power on by keyboard
- Kb power on password
- Hpet suppor
- Hpet mod
- Eup support
- Ac back function
- Case opened
- Bios setup 52
- Sets the warning threshold for cpu temperature when cpu temperature exceeds the threshold bios will emit warning sound options are disabled default 6
- Allows the system to emit warning sound if the cpu system fan is not connected or fails check the fan condition or fan connection when this occurs default disabled
- Reset case open status
- 8 pc health status
- Keeps or clears the record of previous chassis intrusion status enabled clears the record of previous chassis intrusion status and the case opened field will show no at next boot default disabled
- Enables or disables the cpu fan speed control function enabled allows the cpu fan to run at different speed according to the cpu temperature you can adjust the fan speed with easytune based on system requirements if disabled the cpu fan runs at full speed default enabled
- Displays the detection status of the chassis intrusion detection device attached to the motherboard ci header if the system chassis cover is removed this field will show yes otherwise it will show no to clear the chassis intrusion status record set reset case open status to enabled save the settings to the cmos and then restart your system
- Displays the current system voltages
- Displays current system cpu temperature
- Displays current cpu system fan speed
- Current voltage v vcore ddr15v 5v 12v
- Current system cpu temperature
- Current cpu system fan speed rpm
- Cpu warning temperature
- Cpu system fan fail warning
- Cpu smart fan control
- Cpu smart fan mode
- 10 load optimized defaults
- Key to load the safest bios default settings in case system instability occurs you may try to load fail safe defaults which are the safest and most stable bios settings for the motherboard
- Key to load the optimal bios default settings the bios defaults settings help the system to operate in optimum state always load the optimized defaults after updating the bios or after clearing the cmos values
- Bios setup 54
- 9 load fail safe defaults
- When the when the password check item is set to system you must enter the supervisor password or user password at system startup to continue system boot in bios setup you must enter the supervisor password if you wish to make changes to bios settings the user password only allows you to view the bios settings but not to make changes
- When the when the password check item is set to system you must enter the supervisor password or user password at system startup and when entering bios setup
- When a system password is set and the when a system password is set and the password check item in advanced bios features is set to setup you must enter the supervisor password for entering bios setup and making bios changes
- User password
- The bios setup program allows you to specify two separate passwords
- Supervisor password
- Again the message password disabled will appear indicating the password has been can celled
- 55 bios setup
- 11 set supervisor user password
- Bios setup 56
- 13 exit without saving
- 12 save exit setup
- To return to the bios setup main menu
- Chapter 3 drivers installation
- 1 installing chipset drivers
- 3 technical manuals
- 2 application software
- 5 system
- 4 contact
- 7 new utilities
- 6 download center
- System requirements
- Installation and configuration
- Chapter 4 unique features
- Before you begin
- 1 xpress recovery2
- 2 bios update utilities
- 2 1 updating the bios with the q flash utility
- A before you begin
- When updating the bios choose the location where the bios file is saved the following procedure as sumes that you save the bios file to a usb flash drive
- To begin the bios update the monitor will display the update process
- The save main bios to drive option allows you to save the current bios file q flash only supports usb flash drive or hard drives using fat32 16 12 file system if the bios update file is saved to a hard drive in raid ahci mode or a hard drive attached to
- Step 3 when the update process is complete press any key to return to the main menu
- Make sure the bios update file matches your motherboard model
- Key during the post to access q flash
- Do not turn off or restart the system when the system is reading updating the bios do not remove the usb flash drive or hard drive when the system is updating the bios
- B updating the bios
- 65 unique features
- Unique features 66
- To save settings to cmos and exit bios setup the proce dure is complete after the system restarts
- To load bios defaults system will re detect all peripheral devices after a bios update so we recommend that you reload bios defaults
- To load bios defaults
- To exit q flash and reboot the system as the system boots you should see the new bios version is present on the post screen
- 2 2 updating the bios with the bios utility
- C after updating the bios
- B using bios
- A before you begin
- Unique features 68
- The easytune 6 interface
- Tabs information
- Tab function
- Gigabyte s easytune 6 is a simple and easy to use interface that allows users to fine tune their system settings or do overclock overvoltage in windows environment the user friendly easytune 6 interface also includes tabbed pages for cpu and memory information letting users read their system related information without the need to install additional software
- 3 easytune 6
- The dynamic energy save
- Meter mode button information table
- Interface a meter mode
- 4 dynamic energy save
- Total mode button information table
- C stealth mode
- B total mode
- Options descriptions
- Directions for using q share
- 5 q share
- Smart quickboot
- Smart quickboost
- 6 smart
- Smart recovery
- Smart dualbios
- Smart timelock
- Smart recorder
- Selecting a system energy saving mode
- Configuring the bluetooth cell phone key
- Configuring other bluetooth settings
- Auto green is an easy to use tool that provides users with simple options to enable system power savings via a bluetooth cell phone when the phone is out of the range of the computer s bluetooth receiver the sys tem will enter the specified power saving mode
- 75 unique features
- 7 auto green
- The configuration dialog box
- Chapter 5 appendix
- A configuring speakers
- 1 configuring audio input and output
- 1 1 configuring 2 4 5 7 channel audio
- D muting the back panel audio for hd audio only
- C activating an ac 97 front panel audio module
- B configuring sound effect
- A s pdif in
- 1 2 configuring s pdif in out
- B s pdif out
- 1 3 configuring microphone recording
- Enabling stereo mix
- B playing the recorded sound
- A recording sound
- 1 4 using the sound recorder
- To read more faqs for your motherboard please go to the support downloads motherboard faq page on gigabyte s website
- Appendix 84
- 2 troubleshooting
- 2 1 frequently asked questions
- If you encounter any troubles during system startup follow the troubleshooting procedure below to solve the problem
- 85 appendix
- 2 2 troubleshooting procedure
- If the procedure above is unable to solve your problem contact the place of purchase or local dealer for help or go to the support downloads technical service zone page to submit your question our customer service staff will reply you as soon as possible
- Appendix 86
- Weee symbol statement
- Waste electrical electronic equipment weee directive statement
- Restriction of hazardous substances rohs directive statement
- Regulatory notices
- Our commitment to preserving the environment
- 3 regulatory statements
- China restriction of hazardous substances table
- Contact us
- 95 appendix
- To submit a technical or non technical sales market ing question please link to http ggts gigabyte com tw then select your language to enter the system
- Gigabyte global service system
- Appendix 96
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению
-
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе
-
Gigabyte GA-B85TNРуководство пользователя
-
Gigabyte GA-H81TNИнструкция по применению
Изучите настройки BIOS для управления встроенными LAN, IDE контроллерами и последовательными портами. Узнайте, как диагностировать проблемы с кабелем.
