![Gigabyte B550 AORUS ELITE AX — настройки USB и SATA: Конфигурация и поддержка устройств [30/44]](/icons/site-icon-64.png){kind=icon}
Gigabyte B550 AORUS ELITE AX — настройки USB и SATA: Конфигурация и поддержка устройств [30/44]
Превью страниц
Страница 30 /
44
![Gigabyte B550 AORUS ELITE (rev. 1.0) [30/44] Ipv4 pxe support](/views2/1666455/page30/bg1e.png)
USBConguration
& Legacy USB Support
Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)
& XHCI Hand-off
Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off
support. (Default: Enabled)
& USB Mass Storage Driver Support
Enables or disables support for USB storage devices. (Default: Enabled)
& Port 60/64 Emulation
Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support
for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices.
(Default: Disabled)
& Mass Storage Devices
Displays a list of connected USB mass storage devices. This item appears only when a USB storage device
is installed.
NVMeConguration
Displays information on your M.2 NVME PCIe SSD if installed.
SATAConguration
& SATA Mode
Enables or disables RAID for the SATA controllers integrated in the Chipset or congures the SATA controllers
to AHCI mode.
RAID Enables RAID for the SATA controller.
AHCI Congures the SATA controllers to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specication that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug. (Default)
& NVMe RAID mode
Allows you to determine whether to use your M.2 NVMe PCIe SSDs to congure RAID. (Default: Disabled)
& Chipset SATA Port Enable
Enables or disables the integrated SATA controllers. (Default: Enabled)
& Chipset SATA Port 0/1/2/3
Displays the information of the connected SATA device(s).
NetworkStackConguration
& Network Stack
Disables or enables booting from the network to install a GPT format OS, such as installing the OS from
the Windows Deployment Services server. (Default: Disabled)
& IPv4 PXE Support
Enables or disables IPv4 PXE Support. This item is congurable only when Network Stack is enabled.
& IPv4 HTTP Support
Enables or disables HTTP boot support for IPv4. This item is congurable only when Network Stack is
enabled.
& IPv6 PXE Support
Enables or disables IPv6 PXE Support. This item is congurable only when Network Stack is enabled.
& IPv6 HTTP Support
Enables or disables HTTP boot support for IPv6. This item is congurable only when Network Stack is
enabled.
- 30 -
Содержание
263- B550 aorus elite ax b550 aorus elite
- User s manual
- Rev 1002 12me b55aelt 1002r
- Disclaimer
- Identifying your motherboard revision
- Copyright
- Chapter 2 bios setup 2
- B550 aorus elite ax motherboard layout b550 aorus elite ax motherboard block diagram
- Chapter 1 hardware installation
- Table of contents
- Chapter 3 appendix 8
- Motherboard driver disc 5 one g connector
- B550 aorus elite ax motherboard layout
- Box contents
- Two sata cables
- Note only for the b550 aorus elite ax
- B550 aorus elite ax or b550 aorus elite motherboard
- B550 aorus elite ax
- User s manual 5 one antenna
- B550 aorus elite ax motherboard block diagram
- 1 installation precautions
- Chapter 1 hardware installation
- 2 product specifications
- 2 productspecifications
- 4 installing the memory
- Installing the cpu
- 3 installing the cpu
- Dualchannelmemoryconfiguration
- 6 back panel connectors
- Usb 2 1 port
- Sma antenna connectors 2t2r
- Hdmi port
- Displayport
- 5 installing an expansion card
- Usb 3 gen 1 port
- Optical s pdif out connector
- Mic in side speaker out
- Line out front speaker out
- Line in side speaker out
- Center subwoofer speaker out
- Usb 3 gen 2 type a port red
- Usb 3 gen 1 port q flash plus port
- Rj 45 lan port
- Rear speaker out
- Q flash plus butto
- Your device and then remove it from the motherboard
- When removing the cable pull it straight out from the connector do not rock it side to side to
- When removing the cable connected to a back panel connector first remove the cable from
- Prevent an electrical short inside the cable connector
- Please visit gigabyte s website for details on configuring the audio software
- If you want to install a side speaker you need to retask either the line in or mic in jack to be side speaker out through the audio driver
- Audio jack configurations
- 7 internal connectors
- 4 cpu_fan sys_fan1 2 3 fan headers
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- 2 atx_12v atx 2x4 12v power connectors and 2x12 main power connector
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- Overheating overheating may result in damage to the cpu or the system may hang
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- Voltage speed control
- No pin
- Led_cpu cpu cooler led strip rgb led strip header
- For how to turn on off the lights of the led strip please visit the unique features webpage of gigabyte s website
- D_led1 d_led2 addressable led strip headers
- Cpu_opt water cooling cpu fan header
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip
- Connect the cpu cooler led strip rgb led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The headers can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds
- The header can be used to connect a cpu cooler led strip or a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design
- Pwm speed control
- Pin no definition
- Overheating overheating may result in damage to the cpu or the system may hang
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the sata connectors support raid 0 raid 1 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- Sata3 0 1 2 3 sata 6gb s connectors
- Led_c1 led_c2 rgb led strip headers
- For how to turn on off the lights of the led strip please visit the unique features webpage of gigabyte s website
- Connect your rgb led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- Follow the steps below to correctly install an m ssd in the m connector step 1 locate the m connector where you will install the m ssd use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink step 2 locate the proper mounting hole based on the length of your m ssd drive if needed move the standoff to the desired mounting hole insert the m ssd into the m connector at an angle step 3 press the m ssd down and then secure it with the screw replace the heatsink and secure it to the original hole make sure to remove the protective film from the bottom of the heatsink before replacing the heatsink
- The m connectors support m sata ssds or m pcie ssds and support raid configuration please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- Select the proper hole for the m ssd to be installed and refasten the screw and standoff
- M2a_cpu m2b_sb m socket 3 connectors
- Mic2_r 8 no pin
- F_panel front panel header
- Pw power switch connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup settings platform power for more information
- Pled pwr_led power led
- Pin no definition pin no definition
- Nc no connection
- Nc 9 line2_l
- Mic2_l 6 sense
- Line2_r 10 sense
- Hd hard drive activity led connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data
- The front panel design may differ by chassis a front panel module mainly consists of power switch reset switch power led hard drive activity led speaker and etc when connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly
- Gnd 7 faudio_jd
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- System status led
- F_audio front panel audio header
- Speak speaker connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables
- S3 s4 s5 off
- Ci chassis intrusion header connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor
- Res reset switch connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- Tpm trusted platform module header
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- From the power outlet to prevent damage to the usb bracket
- F_usb1 f_usb2 usb 2 1 headers
- F_u32 usb 3 gen 1 header
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord
- You may connect a tpm trusted platform module to this header
- Clr_cmos clear cmos jumper
- Bat battery
- Chapter 2 bios setup
- 1 startup screen
- Advanced mode function keys
- 2 the main menu
- 3 favorites f11
- Spread spectrum control
- Gfx core voltag
- Gfx clock frequenc
- Cpu ratio mod
- Cpu clock ratio
- Cpu clock control
- Ccd0 ccx0 1 rati
- 4 tweaker
- Xmp high frequency suppor
- System memory multiplier
- Svm mode
- Smt mode
- Ppc adjustmen
- Power supply idle contro
- Global c state contro
- Extremememoryprofile x m p
- Downcore control
- Cppc preferred core
- Core performance boos
- Ccd contro
- Amd cool quiet function
- Advanced cpu settings
- Ac back
- 5 settings
- Wake on lan
- Soft off by pwr bttn
- Resume by alarm
- Power loading
- Platform power
- High precision event timer
- Cec 2019 ready
- Uma frame buffer siz
- Pciex16 bifurcation
- Onboard lan controller
- Io ports
- Integrated graphic
- Initial display output
- Hd audio controller
- Display resolutio
- Above 4g decoding
- Uma mod
- Sataconfiguration
- Sata mode
- Port 60 64 emulation
- Nvmeconfiguration
- Nvme raid mode
- Networkstackconfiguration
- Network stack
- Mass storage devices
- Legacy usb support
- Ipv6 pxe support
- Ipv6 http support
- Ipv4 pxe support
- Ipv4 http support
- Chipset sata port enable
- Xhci hand off
- Chipset sata port 0 1 2 3
- Usbconfiguration
- Usb mass storage driver support
- Reset case open status
- Realtek pcie 2 gbe family controller
- Pxe boot wait time
- Pcieslotconfiguration
- Pc health
- Miscellaneous
- Media detect count
- Leds in system power on state
- Leds in sleep hibernation and soft off states
- Case open
- Amd cpu ftpm
- Amd cbs
- 3dmark01 enhancement
- Trusted computing
- Fan control mode
- Temperature warning control
- Temperature interval
- Temperature
- Smart fan 5
- Monitor
- Flow rate
- Fan stop
- Fan speed control
- Fan speed
- Fan fail warning
- Fan control use temperature input
- Cpu vcore cpu vddp dram channel a b voltage 3 v 5v 12v vcore soc
- Access level
- 6 system info
- System time
- System language
- System date
- Q flash
- Plug in devices info
- Security option
- Sata support
- Nvme support
- Full screen logo show
- Fast boot
- Bootup numlock state
- Boot option priorities
- 7 boot
- Lan pxe boot option rom
- Csm support
- Administrator password
- Vga support
- Usb support
- Storage boot option control
- Other pci device rom priority
- Network stack driver support
- User password
- Secure boot
- Preferred operating mode
- Saveprofiles
- Save exit setup
- Loadprofiles
- Load optimized defaults
- Exit without saving
- Boot override
- 8 save exit
- 1 configuring a raid set
- Raid levels
- Configuringtheonboardsatacontroller
- Chapter 3 appendix
- C uefiraidconfiguration
- Before you begin please prepare the following items
- B configuringsatacontrollermodeinbiossetup
- A installing sata hard drive s in your computer
- 1 configuringaraidset
- Installing the operating system
- Install the raid driver and operating system
- 2 drivers installation
- Regulatory notices
- United states of america federal communications commission statement
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte GA-P43T-ES3GРуководство по использованию -
Gigabyte TRX50 AI TOPИнструкция по работе -
Gigabyte GA-EP45-UD3LЭксплуатационная инструкция -
Gigabyte GA-EP45-UD3LRИнструкция к устройству
-
Gigabyte X870E AORUS XTREME AI TOPИнструкция по работе -
Gigabyte GA-MA770-S3Инструкция пользователя -
Gigabyte GA-MA770-DS3Руководство по настройке
-
Gigabyte GA-7VAXРуководство пользователя -
Gigabyte GA-8EGXDR-ECИнструкция по применению -
Gigabyte GA-8EGXDR-EИнструкция по работе
-
Gigabyte B860 EAGLE WIFI6EИнструкция пользователя -
Gigabyte Z490 AORUS ELITE ACРуководство по эксплуатации
Изучите настройки USB и SATA, включая поддержку устройств, режимы RAID и конфигурацию сетевого загрузчика. Оптимизируйте работу вашего оборудования.
