![AEG WS 9-115 419380 [15/121] English](/img/pdf.png)
AEG WS 9-115 419380 [15/121] English
![AEG WS 9-115 419380 [15/121] English](/views2/1009457/page15/bgf.png)
14
English
GB
WARNING!
Read all safety warnings and all instructions, including
those given in the accompanying brochure. Failure to follow
the warnings and instructions may result in electric shock, re and/
or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-O Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush, or cut-o tool. Read all safety warnings,
instructions, illustrations and specications provided with
this power tool. Failure to follow all instructions listed below may
result in electric shock, re and/or serious injury.
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power
tool was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure safe
operation.
d )The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
f) The arbour size of wheels, anges, backing pads or any
other accessory must properly t the spindle of the power
tool. Accessories with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory
and run the power tool at maximum noload speed for one
minute. Damaged accessories will normally break apart during this
test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and shop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of
stopping ying debris generated by various operations. The dust
mask or respirator must be capable of ltrating particles generated
by your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may y away and cause injury beyond immediate area of
operation.
j) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a „live“ wire may make exposed metal parts of the power
tool „live“ and could give the operator an electric shock.
k) Position the cord clear of the spinning accessory. If you lose
control, the cord may be cut or snagged and your hand or arm may be
pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has come
to a complete stop. The spinning accessory may grab the surface
and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents. The motor’s fan
will draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near ammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or shock.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel.
Pinching or snagging causes rapid stalling of the rotating wheel
which in turn causes the uncontrolled power tool to be forced in the
direction opposite of the wheel‘s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch point
can dig into the surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward or away from
the operator, depending on direction of the wheel’s movement at
the point of pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a rm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool will
move if kickback occurs. Kickback will propel the tool in direction
opposite to the wheel’s movement at the point of snagging.
Содержание
- 105 101 97 93 89 85 81 77 73 69 65 61 57 49 53 45 41 37 33 29 25 21 17 13 109 113 2
- Deutsch 2
- English 2
- Español 2
- Français 2
- Hvratski 2
- Italiano 2
- Latviski 2
- Lietuv 2
- Magyar 2
- Nederlands 2
- Polski 2
- Português 2
- Romănia 2
- Slovensko 2
- Slovensky 2
- Svenska 2
- Türkçe 2
- Česky 2
- Български 2
- 中文 2
- 配件 3
- A b c d e 10
- English 14
- English 15
- English 16
- English 17
- Deutsch 18
- Deutsch 19
- Deutsch 20
- Deutsch 21
- Français 22
- Français 23
- Français 24
- Français 25
- Italiano 26
- Italiano 27
- Italiano 28
- Italiano 29
- Español 30
- Español 31
- Español 32
- Español 33
- Português 34
- Português 35
- Português 36
- Português 37
- Nederlands 38
- Nederlands 39
- Nederlands 40
- Nederlands 41
- Svenska 50
- Svenska 51
- Svenska 52
- Svenska 53
- Ελ el 58
- Ειδικeσ υποδειξεισ ασφαλειασ 59
- Türkçe 62
- Türkçe 63
- Türkçe 64
- Türkçe 65
- Česky 66
- Česky 67
- Česky 68
- Česky 69
- Slovensky 70
- Slovensky 71
- Slovensky 72
- Slovensky 73
- Polski 74
- Polski 75
- Polski 76
- Polski 77
- Magyar 78
- Magyar 79
- Magyar 80
- Magyar 81
- Slovensko 82
- Slovensko 83
- Slovensko 84
- Slovensko 85
- Hrvatski 86
- Hrvatski 87
- Hrvatski 88
- Hrvatski 89
- Latviski 90
- Latviski 91
- Latviski 92
- Latviski 93
- Lietuviškai 94
- Lietuviškai 95
- Lietuviškai 96
- Lietuviškai 97
- Рус 102
- Ðåêîìåíäàöèè ïî òåõíèêå áåçîïàñíîñòè 103
- Рус 103
- Рус 104
- Winnenden 2010 12 09 105
- Рус 105
- Бъл 106
- J дръжте уреда за изолираните ръкохватки когато извършвате работи при които режещият инструмент може да засегне скрити електроинсталационни кабели или собствения си кабел контактът на режещия инструмент с тоководещ проводник може да предаде напрежението върху метални части на уреда и да доведе до токов удар 107
- N почиствайте редовно вентилационните отвори на вашия електрически уред вентилаторът на двигателя засмуква прах в корпуса а събирането на метален прах може да доведе до електрически повреди o не работете с електрическата машина в близост до запалими материали искрите могат да възпламенят тези материали p не използвайте такива инструменти които трябва да се охлаждат с течности употребата на вода или на други течни охлаждащи средства може да доведе до токов удар 107
- А този електроуред се използва като шлайф телена четка и ъглошлайф обърнете внимание на указанията за безопасност съветите изображенията и данните които ще получите заедно с електроинструмента ако не спазите следните указания може да се стигне до токов удар пожар и или тежки наранявания 107
- Ако се използва за цели за които не е предвиден този електроуред може да доведе до опасност и наранявания 107
- Бъл 107
- Внимание прочетете указанията за безопасност и съветите в приложената брошура 107
- Ритане на машината и съответни указания за безопасност ритането е внезапна реакция на машината вследствие на закачил се или блокиран въртящ се инструмент напр шлайфаща шайба шлайфащ диск телена четка и др закачането или блокирането води до внезапно спиране на въртящия се инструмент по този начин на мястото на блокиране машина се ускорява неконтролирано срещу посоката на въртене на инструмента 107
- Специални указания за безопасност 107
- Бъл 108
- Бъл 109
- Romănia 110
- Romănia 111
- Romănia 112
- Romănia 113
- 特殊安全指示 119
- Ws 12 125 xe 120
- 正确地使用机器 120
- 电子 120
- 电源插头 120
- 符号 120
- 维修 120
- 4250 09 121
- W w w a e g p t c o m 121
Похожие устройства
- AEG FS 140 416090 Инструкция по эксплуатации
- AEG EX 125 ES 416100 Инструкция по эксплуатации
- AEG GS 500 E 412985 Инструкция по эксплуатации
- AEG PS 305 DG 411570 Инструкция по эксплуатации
- AEG US 1300 XE 413235 Инструкция по эксплуатации
- AEG OF 2050 E 403665 Инструкция по эксплуатации
- AEG WS 12-125 XE 419430 Инструкция по эксплуатации
- AEG HBS 1000 E 413205 Инструкция по эксплуатации
- AEG PE 150 412266 Инструкция по эксплуатации
- AEG WS 9-125 419390 Инструкция по эксплуатации
- AEG WSC 14-125 MX 412233 Инструкция по эксплуатации
- AEG WS 11-125 419410 Инструкция по эксплуатации
- AEG BSB 14G NC-142C 431989 Инструкция по эксплуатации
- AEG BSB 18C LI-402C 443997 Инструкция по эксплуатации
- AEG SB 20 2E 411000 Инструкция по эксплуатации
- AEG 412396 Инструкция по эксплуатации
- AEG SBE 600 R KIT 381720 Инструкция по эксплуатации
- AEG SBE 570 R 412681 Инструкция по эксплуатации
- AEG COMPACT BS 12C2 LI-152B 446903 Инструкция по эксплуатации
- AEG BSB 18 LI 411280 Инструкция по эксплуатации