![Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [191/555] 12053](/img/pdf.png)
Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [191/555] 12053
![Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [191/555] 12053](/views2/1012781/page191/bgbf.png)
Section 02 ENGINE
Subsection 11 (CYLINDER BLOCK)
Close puller claws so that they can be inserted
in end bearing. Holding claws, turn puller shaft
clockwise so that claws open and become firmly
tight against bearing.
Slide puller hammer outwards and tap puller end.
Retighten claws as necessary to always maintain
them tight against bearing. Continue this way un-
til bearing completely comes out.
Cylinder Block Inspection
Cylinder
Check cylinder for cracks, scoring and wear ridges
on the top and bottom of the cylinder. If so, re-
place cylinder.
Cylinder Taper
Measure cylinder bore and if it is out of specifica-
tions, re-hone cylinder sleeve and replace piston
with first oversize.
NOTE: It is not necessary to have all cylinders
re-honed if they are not all out of specification.
Mixed standard size and oversize cylinders are
allowed.
Measure cylinder bore at 3 recommended posi-
tions. See the following illustration.
R1503motr24A
3
1
2
B
A
1. First m
easuring diameter
2. Second measuring diameter
3. Third measuring diameter
A. 60 mm (2
.362 in)
B. 110 mm (4.331in)
CYLINDER TAPER IN DIAMETER
NEW MAXIMUM
0.038 mm (.001 in)
SERVICE LIMIT
0.090 mm (.004 in)
Distance between measurements should not ex-
ceed the service limit mentioned above.
Cylinder Out of Round
Measure cylinder diameter in piston axis direction
from top of cylinder. Take an other measurement
90° from first one and compare.
NOTE: Take the same measuring points as de-
scribed in
CYLINDER TAPER
above.
A
R1503motr25A
B
A. Perpendicular to crankshaft axis
B. Parallel t
o crankshaft axis
CYLINDER OUT OF ROUND
NEW MAXIMUM
0.008 mm (.0003 in)
SERVICE LIMIT
0.015 mm (.0006 in)
Bearings
To measure the wear of the crankshaft bearings
no. 13 and no. 14 and balancer shaft bearings
no. 15, both cylinder block halves with OLD
bearings have to be screwed together as per
tightening procedure described below.
Measure the inside diameter of the bearings with
a bore gauge.
1
R1503motr33A
ENGI
NE UPSIDE DOWN
1. Bore gauge
168
smr2009-026
Похожие устройства
- Craftsman 38901 Инструкция по эксплуатации
- Samsung GW77NMR-X Инструкция по эксплуатации
- Delonghi ESAM 6620 Инструкция по эксплуатации
- Yamaha CPX-700 SDB Инструкция по эксплуатации
- Haier JC-110GDD Инструкция по эксплуатации
- Panasonic SC-HT05 Инструкция по эксплуатации
- Can-Am Spyder RT SE5 2010 Инструкция по эксплуатации
- Delonghi KG 49 Black Инструкция по эксплуатации
- Partner P40-450C 9620001-12 Инструкция по эксплуатации
- Samsung CE-2738 NR Инструкция по эксплуатации
- Haier JC-160GD Инструкция по эксплуатации
- Yamaha FX-370C Инструкция по эксплуатации
- Can-Am Spyder RT SM5 2010 Инструкция по эксплуатации
- Panasonic SC-DT310 Инструкция по эксплуатации
- Simplicity ERDS16550 881247 Инструкция по эксплуатации
- Delonghi KG 40 Black Инструкция по эксплуатации
- Samsung GE89ASTR Инструкция по эксплуатации
- Yamaha FX-370C BL Инструкция по эксплуатации
- Haier ZW-266 Инструкция по эксплуатации
- Opel Vectra B Инструкция по эксплуатации