![Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [465/555] 12053](/img/pdf.png)
Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [465/555] 12053
![Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [465/555] 12053](/views2/1012781/page465/bg1d1.png)
Section 07 BODY AND HULL
Subsection 01 (SUSPENSION (iS))
5. Leak on hydraulic circuit.
- Repair or replace defective part(s).
6. Faulty suspension position sensor.
- Test sensor and replace as required.
7. Actuator is damaged.
- Replace the actuator.
8. Hydraulic pump cannot build enough pressure.
- Replace hydraulic pump.
SUSPENSION MOVES ERRATICALLY.
1. Defective shock absorber.
- Replace the shock absorber.
2. Broken spring(s).
-Replacespring(s).
SUSPENSION NOISE (DURING A TURN).
1. Front or rear suspension arm shaft supports po-
sition.
- Supports must be leaned against both ends of
shaft. Reposition shaft in its supports.
2. Worn arm shaft bushings.
- Check front and rear arm shaft bushings condition
and replace as required.
3. Snap rings on both sides of the rear lower arm
shaft are not properly positioned.
- Reposition shaft in its supports.
SUSPENSION NOISE (FRONT OF SEAT).
1. Screws retaining holders are loosened.
- Tighten shock absorber and actuator holder
screws to recommended torque.
2. Shock absorber screws are loosened.
- Tighten shock absorber screws to recommended
torque.
3. Link under actuator holder loosened or not in-
stalled.
- Install link properly.
- Tighten bolts to recommended torque.
SUSPENSION IS LOWER THAN THE DOCK
MODE POSITION.
1. Spring (s) out of specification or broken.
- Replace the defective spring(s).
2. Bump stops damaged or worn.
- Replace both bump stops.
SUSPENSION BOTTOMS HARD.
1. Spring(s) out of specification or broken.
- Replace the defective spring(s).
2. Shock absorber is damaged.
- Check shock absorber resistance. Replace shock
absorber.
3. Bump stops damaged or worn.
- Replace both bump stops.
SUSPENSION QUIT WORKING BUT
MAY OPERATES MOMENTARILY AFTER
RESTARTING THE ENGINE.
1. Hydraulic pump current draw is too high.
- Check hydraulic pump.
2. Internal problem inside iS module.
- Replace iS module.
442 smr2009-041
Похожие устройства
- Craftsman 38901 Инструкция по эксплуатации
- Samsung GW77NMR-X Инструкция по эксплуатации
- Delonghi ESAM 6620 Инструкция по эксплуатации
- Yamaha CPX-700 SDB Инструкция по эксплуатации
- Haier JC-110GDD Инструкция по эксплуатации
- Panasonic SC-HT05 Инструкция по эксплуатации
- Can-Am Spyder RT SE5 2010 Инструкция по эксплуатации
- Delonghi KG 49 Black Инструкция по эксплуатации
- Partner P40-450C 9620001-12 Инструкция по эксплуатации
- Samsung CE-2738 NR Инструкция по эксплуатации
- Haier JC-160GD Инструкция по эксплуатации
- Yamaha FX-370C Инструкция по эксплуатации
- Can-Am Spyder RT SM5 2010 Инструкция по эксплуатации
- Panasonic SC-DT310 Инструкция по эксплуатации
- Simplicity ERDS16550 881247 Инструкция по эксплуатации
- Delonghi KG 40 Black Инструкция по эксплуатации
- Samsung GE89ASTR Инструкция по эксплуатации
- Yamaha FX-370C BL Инструкция по эксплуатации
- Haier ZW-266 Инструкция по эксплуатации
- Opel Vectra B Инструкция по эксплуатации