Home
Главная
Sea-Doo
Гидроцикл
GTX Limited iS 2009
Инструкция по эксплуатации Страница: 505

Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [505/555] 12053

Section 07 BODY AND HULL

Subsection 02 (BODY)

For dirt build-up, use BRP PLASTIC & VINYL

CLEANER (P/N 413 711 200)

, Vinyl Finish Vinyl

Cleaner or an equivalent. Let soak for approxi-

mately 10 minutes, then gently scrub with a soft

bristle brush. For specific stain removal, refer to

your cleaning and care card.

Do not use any silicone-based protectants. They

will extract the plasticizers, leaving the vinyl hard

and brittle, and eventually cracking will occur.

RECOMMENDED PRODUCTS

BRP Plastic a

nd Vinyl Cleaner

(P/N 413 711 200)

Dish Soap (Da

wn or Ivory)

3. Fantastik

3M Citrus Cleaner

303 Protect

ant

Vinyl Clea

ning Recommendations for Special

Stains

TYPE OF

STAIN

STEP

ACTION

Ballpoin

tink*

EBA

Chewing gum D A

—

Coffee, tea,

chocolat

——

A. Medium-soft brush,

warm soap

y water,

rinse/dry.

Pen D B

—

Grease D B

—

Househo

ld soil

—

B. Vinyl

Finish Cleaner,

rinse/dry.

Ketchup A B

—

Latex paint A B

—

Lipsti

—

Mildew or wet

leaves*

CBA

Motor o

——

C. One (1) tablespoon

of ammonia, one-fourth

(1/4) c

up of hydrogen

peroxide, three-fourth

(3/4) cup of water,

rinse/

dry.

Oil-based paint D B

—

Permanent

marke

EBC

Spray paint B B

—

D. Wipe

or scrape off

excess (chill gum with

ice before hand).

Suntan lotion A B

—

Tar/a

sphalt

—

Yellow mustard A B C

E. Denatured alcohol,

rinse/dry.

* Suntan lotion, tree pollen, wet leaves and some other

prod

ucts can contain dyes that stain permanently.

All cleaning methods must be followed by a thor-

ough rinse with warm water.

Certain household cleaners, powdered abrasives,

steel wool and industrial cleaners can cause dam-

age and discoloration and are not recommended.

Dry cleaning fluids and lacquer solvents should

not be used as they will remove printed pattern

andgloss. Waxesshouldbeusedwithcaution

as many contain dyes or solvents that can perma-

nently damage the protective coating.

SEAT LATCH

Seat Latch Adjustment

NOTE: Apply LOCTITE 243 (BLUE) (P/N 293 800 060)

on threads of lock pin when the adjustment is re-

quired or when the lock pin is removed. If a new

lock pin is used, it is already coat with a thread-

locker.

1. Loosen adjustment nut.

2. Adjust lock pin height. Do not torque yet.

3. Close and latch seat.

4. Pull lock pin rearward and tighten adjustment

nut.

smr2009

-042-033_a

1. Lock pin

2. Adjustment nut. Torque to 8 N•m (71 lbf•in)

A. 32.0 mm

± 0.5 mm (1.26 in ± .02 in)

BUMPER

Bumper Removal

Front B

umper

1. Remove both protective caps.

482 smr2009-042

Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [505/555] 12053

Похожие устройства