Jetair CH MilanoE90X+П/ДУ Инструкция по эксплуатации онлайн [6/32] 132917
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Jetair CH MilanoE90X+П/ДУ Инструкция по эксплуатации онлайн [6/32] 132917

Jetair CH MilanoE90X+П/ДУ Инструкция по эксплуатации онлайн [6/32] 132917
J132
6
GB
INSTALLATION
- Once installed, the appliance must be no less than
65 cm away from an electric hob and no less than
65 cm away from gas burners or a mixed hob.
- If the instructions for the installation of the gas hob specify
a greater distance, please take this into account.
USE
The hood is designed to be used either to filter and re-
circulate air or in a ducted vented mode.
OUTDOOR VENTED INSTALLATION
To use the hood in the vented mode, you need to
connect a flexible pipe to the connector “A” (fig. 1),
which should then be fastened to the ceiling.
VENTLESS FILTERING INSTALLATION
When the air cannot be vented to the outside, the hood
can be fitted with an activated carbon filter.
The air is purified by the filter and re-circulated into
the room via the grids on the flues.
To switch from “Vented” to “Ventless” operation, contact
your retailer or the manufacturer for the relevant
assembly kit.
ELECTRICAL CONNECTION
Before making any electrical connections, make sure
that the voltage of the electrical mains corresponds
with the value indicated on the appliance rating sticker.
It is highly recommended that the electrical connection
be made by a qualified electrician.
APPLIANCE FITTED WITH A PLUG
Insert the plug into a socket that complies with the
applicable norms in force.
Once plugged into the socket, the plug must be easily
accessible.
If you intend to connect the hood directly to the electrical
mains, remove the plug and add a standard bipolar
switch with a minimum contact opening of 3mm.
APPLIANCE NOT FITTED WITH A PLUG
Fit a standard plug or a standard bipolar switch
compliant with the applicable norms in force, with a
minimum contact opening of 3mm.
The manufacturer will not be held responsible for any
problems arising from failure to comply with the above
instructions.
CLASS 1 APPLIANCES MUST BE EARTHED
The connection must be made as follows:
BROWN = L (current)
BLUE = N (neutral)
YELLOW/GREEN = (earth)
MAINTENANCE
Disconnect the appliance from the electrical power
supply before performing any maintenance operations
on the same.
The correct operation of the hood is directly related to
how often it is cleaned and serviced, especially the
aluminium grids and the activated carbon filter.
The grids trap any grease particles and solids sus-
pended in the air.
They therefore tend to clog over time, depending on
how often the hood is used and on the type of cooker
installed.
The forged aluminium grids should be washed by
hand or in your dishwasher, and allowed to dry
thoroughly before remounting.
Failure to comply with the washing instructions could
result in a fire hazard.
The activated carbon filter is only used by the ventless,
filtering version, and is designed to trap odours and
clean the air.
The carbon filter is saturated after a varying amount
of time depending on the type of cooker used and on
how regularly the aluminium grids are cleaned.
Replace the carbon filter when prompted to do so by
the LED indicator light “F” (electronic version).
In any case, in the absence of such prompting, the
cartridge must be replaced at least once every four
months.
CLEANING THE HOOD
Wipe the exterior of the hood with a cloth dampened
with denatured alcohol or mild liquid detergents. Avoid
using abrasive products.
Wipe off all deposits from the fan and other hood
surfaces frequently, using the above products.
ATTENTION: SAFETY WARNINGS
The cooking vapours must not be vented to the outside
along a flue used for venting combustion fumes or
gases, nor along a duct used as a flue for rooms in

Содержание

Похожие устройства

Скачать