![Kramer VP-161xl [12/37] Installing on a rack](/img/pdf.png)
Kramer VP-161xl [12/37] Installing on a rack
![Kramer VP-161xl [12/37] Installing on a rack](/views2/1152377/page12/bgc.png)
Installing on a Rack
9
5 Installing on a Rack
This section describes what to do before installing on a rack and how to rack
mount
1
.
Before installing on a rack, be sure that the environment is
within the recommended range:
Operating temperature range +5 to +45 Deg. Centigrade
5 to 65% RHL, non-condensing
-20 to +70 Deg. Centigrade
5 to 95% RHL, non-condensing
Operating humidity range
Storage temperature range
Storage humidity range
When installing on a 19" rack, avoid hazards by taking
care that:
It is located within the recommended environmental
conditions, as the operating ambient temperature of a
closed or multi unit rack assembly may exceed the
room ambient temperature.
Attach both ear brackets to the
machine. To do so, remove the
screws from each side of the machine
(3 on each side), and replace those
screws through the ear brackets.
Place the ears of the machine
against the rack rails, and insert the
proper screws (not provided) through
each of the four holes in the rack
ears.
Note that:
Detachable rack ears can be removed
for desktop use
Always mount the machine in the rack
before you attach any cables or
connect the machine to the power
If you are using a Kramer rack adapter
kit (for a machine that is not 19"), see
the Rack Adapters user manual for
installation instructions (you can
download it at:
http://www.kramerelectronics.com)
In some models, the front panel
may feature built-in rack ears
Once rack mounted, enough air will still flow around the
machine.
The machine is placed straight in the correct horizontal
position.
You do not overload the circuit(s). When connecting
the machine to the supply circuit, overloading the
circuits might have a detrimental effect on overcurrent
protection and supply wiring. Refer to the appropriate
nameplate ratings for information. For example, for
fuse replacement, see the value printed on the product
label.
The machine is earthed (grounded) in a reliable way
and is connected only to an electricity socket with
grounding. Pay particular attention
and that you use only the power cord that is
supplied with the machine.
to situations where
electricity is supplied indirectly (when the power cord is
not plugged directly into the socket in the wall), for
example, when using an extension cable or a power
strip,
CAUTION!!
Before Installing on a Rack
How to Rack Mount
To rack-mount a machine:
1
1
2
2
3
4
5
1 This section applies to VP-81xl, VP-161xl and VP-321xl
Содержание
- Kramer electronics ltd 1
- Models 1
- User manual 1
- Contents 2
- Figures 3
- Tables 3
- Getting started 4
- Introduction 4
- Audio connections are not shown 5
- Getting started 5
- Overview 6
- Your xga audio switcher 6
- Figure 1 vp 81xl 8x1 xga audio switcher 7
- Table 1 front panel vp 81xl 8x1 xga audio switcher features 7
- Table 2 rear panel vp 81xl 8x1 xga audio switcher features 7
- Your xga audio switcher 7
- Figure 2 table 3 and table 4 define the vp 161xl 16x1 xga audio switcher 8
- Figure 2 vp 161xl 16x1 xga audio switcher 8
- The vp 161xl is a 16x1 switcher for vga xga signals and balanced audio stereo signals that lets you route one of up to 16 inputs to one output 8
- Vp 161xl 16x1 xga audio switcher 8
- Your xga audio switcher 8
- Table 3 front panel vp 161xl 16x1 xga audio switcher features 9
- Table 4 rear panel vp 161xl 16x1 xga audio switcher features 9
- Your xga audio switcher 9
- Figure 3 table 5 and table 6 define the vp 321xl 32x1 xga audio switcher 10
- Figure 3 vp 321xl 32x1 xga audio switcher 10
- The vp 321xl is a 32x1 switcher for vga xga signals and balanced audio stereo signals that lets you route one of up to 32 inputs to one output 10
- Vp 321xl 32x1 xga audio switcher 10
- Your xga audio switcher 10
- Table 5 front panel vp 321xl 32x1 xga audio switcher features 11
- Table 6 rear panel vp 321xl 32x1 xga audio switcher features 11
- Your xga audio switcher 11
- Installing on a rack 12
- Connecting an xga audio switcher 13
- 4 set the machine see section 18
- Configure the vp 81xl vp 161xl and or vp 321xl unit by setting the 12 setup dipswitches item 13 on the rear panel as figure 9 and table 7 define 18
- Connecting an xga audio switcher 18
- Dipswitch settings 18
- Figure 9 setup dipswitches factory default for stand alone machine 1 18
- Setting the machine 18
- Table 7 dipswitch definitions 18
- Table 8 machine dipswitch settings 18
- To control a unit via rs 232 or rs 485 each unit has to be identified via its unique machine set the machine on a vp 81xl vp 161xl and or vp 321xl unit according to table 8 a valid machine is from 1 to 15 for a single stand alone machine set as machine 1 18
- Connecting an xga audio switcher 19
- Dipswitches 19
- Figure 10 dipswitch settings on 4 vp 81xl vp 161xl and or vp 321xl units 19
- Figure 10 illustrates how to set the dipswitches on four single vp 81xl vp 161xl and or vp 321xl units which are controlled by one rs 232 port 19
- Machine 1 19
- Machine 2 19
- Machine 3 19
- Machine 4 19
- Connecting an xga audio switcher 21
- Table 9 machine address dipswitch settings 21
- Connect remote contact closure switches to the remote terminal block connector for example to a single xga audio switcher such as the vp 81xl as figure 12 describes a remote unit can consist of a mechanical switche 23
- Connecting an xga audio switcher 23
- Connecting the remote terminal bloc 23
- Connector 23
- Figure 11 three looped vp 81xl units interconnected video connections shown 23
- Figure 12 connecting a remote mechanical switcher unit to the vp 81xl 23
- With a common wire for groun 23
- You can also connect remote contact closure switches to the remote terminal block connectors according to table 9 the example in figure 13 illustrates how to connect remote contact closure switches to the remote terminal block connectors on a set of three looped vp 81xl units 24
- Operating your xga audio switcher 25
- Flash memory upgrade 28
- Of the vp 81xl vp 161xl vp 321xl 34
- Table 10 includes the technical specifications 34
- Table 10 technical specification 34
- Technical specifications 34
- Table 11 lists the hex values for a single vp 81xl vp 161xl vp 321xl machine for more detailed information see protocol 200 35
- Table 11 vp 81xl vp 161xl vp 321xl hex codes 35
- Table of hex codes for serial communication 35
- All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty 36
- Except as below this warranty covers all defects in material or workmanship in this product the following are not covered by the warranty 36
- Kramer electronics hereafter kramer warrants this product free from defects in material and workmanship under the following terms 36
- Labor and parts are warranted for seven years from the date of the first customer purchase 36
- Only the first purchase customer may enforce this warranty 36
- The liability of kramer for any effective products is limited to the repair or replacement of the product at our option kramer shall not be liable for 36
- This warranty gives you specific legal rights and you may also have other rights which vary from place to place note all products returned to kramer for service must have prior approval this may be obtained from your dealer this equipment has been tested to determine compliance with the requirements of en 50081 electromagnetic compatibility emc generic emission standard part 1 residential commercial and light industry en 50082 electromagnetic compatibility emc generic immunity standard part 1 residential commercial and light industry environment cfr 47 fcc rules and regulations part 15 radio frequency devices subpart b unintentional radiators 36
- We will pay labor and material expenses for covered items we will not pay for the following 36
- Caution 37
- For the latest information on our products and a list of kramer distributors visit our web site www kramerelectronics com where updates to this user manual may be found we welcome your questions comments and feedback 37
- Kramer electronics ltd 37
- Safety warning safety warning 37
Похожие устройства
- Kramer WSI-1VGA Руководства по эксплуатации
- Kramer SI-1VGA Руководства по эксплуатации
- Kramer VS-21HDCP-IR Руководства по эксплуатации
- Kramer VS-41HDCP Руководства по эксплуатации
- Kramer VS-21H-IR Руководства по эксплуатации
- Kramer VS-211HA Руководства по эксплуатации
- Kramer VS-41HC Руководства по эксплуатации
- Kramer VS-41H Руководства по эксплуатации
- Kramer VS-81H Руководства по эксплуатации
- Kramer VS-161H Руководства по эксплуатации
- Kramer VS-12DP-IR Руководства по эксплуатации
- Kramer VS-21DP-IR Руководства по эксплуатации
- Kramer DIP-20 Руководства по эксплуатации
- Kramer DIP-20 Инструкция по установке
- Kramer DIP-30 Инструкция по установке
- Kramer DIP-30 Руководства по эксплуатации
- Kramer VP-81SIDN Руководства по эксплуатации
- Razer Orochi 2013 (RZ01-00820100-R3G1) Инструкция по эксплуатации
- Razer Nabu X White (RZ15-01290200-R3G1) Инструкция по эксплуатации
- Razer Firefly (RZ02-01350100-R3M1) Инструкция по эксплуатации