![Parsun F6BMS [2/93] Notice](/img/pdf.png)
Parsun F6BMS [2/93] Notice
![Parsun F6BMS [2/93] Notice](/views2/1155982/page2/bg2.png)
NOTICE
This manual includes service instructions for F4, F5, and has been prepared by Parsun
Power primarily for use by the dealers when performing maintenance and repair to
Parsun outboard engines. Before performing maintenance, please read the manual
carefully. When performing maintenance and repair to Parsun outboard engines, please
use the service procedure and tools recommended by the manual. If you use other
service procedure and tools, please follow guidance from experienced maintenance
people, to avoid damage to people and outboard engines.
The manual is based on the sample machines that are produced at the time of printing, so
the model being actual purchased may differ a little from the descriptions and
illustrations given in this manual. If necessary, our company will distribute the manual
revision to dealers.
In this Service Manual, particularly important information is distinguished in the
following ways. Please ready the manual carefully, and perform the instructions
correctly and carefully.
WARNING:
Failure to follow WARNING instructions could result in severe injury or death to the
machine operator and bystander.
CAUTION:
A CAUTION indicates special precautions that must be taken to avoid damage to the
outboard motor.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
The common troubles and solutions are given in the end of the manual, please ready
carefully. When performing maintenance and repair to Parsun outboard engines, they will
help you judge the outboard engine’s status quickly and improve the work efficiency.
All rights reserved.
This manual cannot be reproduced or
transmitted in any form or by any means
without the written approval of our
company.
Suzhou Parsun Power Machine Co., Ltd.
Содержание
- F4bm f5bm 1
- Parsun outboard engine service manual 1
- Notice 2
- Emergency start 7
- General information 7
- Identifecation 7
- Propeller selection 7
- Disassembly and assembly 9
- Safety while working 9
- One time use parts 10
- Pre delivery check 10
- Special tools and detection device 12
- L 1277 14
- Bracket 15
- Description 15
- Dimension 15
- Drive unit 15
- Fuel and oil 15
- Item description item description 15
- Outboard engine specifications 15
- Performance 15
- Power unit 15
- Specifications 15
- Weight 15
- 59 2mm 16
- Cylinder 16
- Item description item description 16
- Maintenance information 16
- Piston 16
- Piston ring 16
- Power unit 16
- 0 6 ω 17
- 7 k ω 17
- Btdc28º 32º 17
- Camshaft 17
- Cont d item description item description 17
- Ignition system ignition system 17
- Item description item description 17
- Power unit 17
- Specified torque part to be tightened part name thread size quantity torque 17
- T c i air gap 0 0 mm 17
- Tightening torque 17
- Cont d part to be tightened part name thread size quantity torque 18
- General torque 18
- Lower unit 18
- Mm m10 36 nm 18
- Mm m12 43 nm 18
- Mm m5 5nm 18
- Mm m6 8 nm 18
- Mm m8 18 nm 18
- Nut a bolt b torque 18
- Power unit 18
- Upper unit 18
- Fuel system 19
- Maintenance time table 19
- Periodic service 19
- Power unit 20
- Control system 22
- Lower unit 24
- General inspection 25
- Recoil starter 26
- Explosive drawing 27
- Disassembling 30
- Starter rope replacement 30
- Disassembling and inspection 31
- Adjust the adjusting nut on the tightwire of the dent a 32
- Assembling 32
- Installation 32
- Explosive drawing 33
- Ignition system 33
- Notice 33
- Spark plug ignition 34
- Wiring diagram 34
- Flywheel maintenance 35
- Ignition coil inspection 35
- Spark plug cap 35
- Explosive drawing 36
- Fuel system 36
- Notice 36
- Fuel tank removal and inspection 42
- Open the top cowling 42
- Remove the fuel pipe from fuel tank 42
- Remove the starter pull the fuel tank out 42
- Remove three bolts fixing the starter 42
- Fuel joint removal and inspection 43
- Oil switch removal and inspection 43
- Fuel pump removal and inspection 44
- Intake system removal and inspection 45
- Explosive drawing 46
- Notice 46
- Power unit 46
- To prevent the engine from accidental starting you should adopt adequate safeguard measures to cut off the ignition system for example remove the hang rope stopper from stop switch assembly and remove spark plug cap from spark plug 46
- 1 2 1 1 1 2 1 1 1 54
- 箱盖减磨片 曲轴组件 连杆螺栓 连杆组件 活塞 活塞销 活塞销卡簧 组合油环 气环2 气环1 54
- Carry the power unit and put it onto the working table 55
- Disassembling and inspection 55
- Disassembling power unit from outboard engine 55
- Housing bearing installer oil seal installer tool h 55
- Open the top cowling 55
- Remove air filter and carburetor 55
- Remove bolts connecting the engine and upper casing 55
- Remove choke cable and throttle cable 55
- Remove the starter and fuel pump 55
- Special tools 55
- Cylinder cover 56
- Disassembling 56
- Top cowling 64
- Upper unit 64
- F4 06000006 f4 06000004 66
- Bottom cowling 67
- Explosive drawing 70
- Remove top cowling clamp lever bush a and clamp lever bush b 5 remove wave washer 6 inspect if bottom cowling is cracked or damaged replace if necessary 7 inspect if clamp lever handle is cracked or damaged replace if necessary 8 inspect if clamp lever is cracked or damaged replace if necessary 9 inspect if wave washer and clamp lever bush are cracked or damaged replace if necessary 70
- Steering handle 70
- Disassembling and inspection 1 remove steering handle cover 2 remove handle bush bush washer and wave washer 3 remove steering handle shocker damper 72
- Bracket 74
- Explosive drawing 74
- Disassembling and inspection 1 remove tilt locked clasp 2 remove swivel bracket cover 3 remove bottom shock absorption assembly and shock absorption bush 77
- Explosive drawing 79
- Upper unit 79
- Type s 2 80
- 平垫圈6 80
- 空心定位销 80
- Disassembling and inspection 1 remove the water tube 2 remove the gear shift handle and change shaft 3 remove the shift rod and shift rod lever 81
- 孔用弹性挡圈22 驱动轴橡胶衬套 驱动轴衬套 81
- 接长体 81
- 水上装置壳体 变档轴密封圈 81
- 进水管 工形橡胶圈 81
- Lower unit 82
- Water pump assembly 82
- Explosive drawing 83
- Disassembling and inspection 1 remove cotter pin and nut assy 2 remove propeller assembly and spacer 3 remove the lower casing cover 89
- Common troubles and solutions 92
- Trouble type possible reason recovery action 92
- Cont d trouble type possible reason recovery action 93
Похожие устройства
- Parsun F6BMS Руководство по эксплуатации
- Parsun F9.8BMS Руководство по эксплуатации
- Parsun F9.8BMS Каталог запчастей
- Sanus MF209-S2 Инструкция по эксплуатации
- Sanus VMF308-B2 Black Инструкция по эксплуатации
- Sanus VLF311-B1 Black Инструкция по эксплуатации
- Sanus VLF320-B1 Black Инструкция по эксплуатации
- Sanus VM300 S Инструкция по эксплуатации
- Sanus VMPL S Инструкция по эксплуатации
- Sanus VM1 S Инструкция по эксплуатации
- Sanus VMF S Инструкция по эксплуатации
- Sanus VM3 S Инструкция по эксплуатации
- Sanus VM2 S Инструкция по эксплуатации
- Sanus VM200 S Инструкция по эксплуатации
- Sanus VMDD26 S Инструкция по эксплуатации
- Sanus VMAA26 S Инструкция по эксплуатации
- Sanyo PLC-XR201 Инструкция по эксплуатации
- Saturn 1200 Инструкция по эксплуатации
- Saturn 1045 Инструкция по эксплуатации
- Saturn 1006 Инструкция по эксплуатации