Bosch tds 2251 [18/150] D fabric protection soleplate cover

Bosch tds 2251 [18/150] D fabric protection soleplate cover
18
B O S C H
ENglISH
To wash the scale collector, place it under the water
tap and wash it up until calc residues are removed.
Squeeze it as indicated in the picture a).
To obtain the best result, you may immerse the scale
collector for approximately 30 minutes in tap water
(250 ml) mixed with a measure (25 ml) of descaling
uid, as indicated in the picture b). Then, rinse it
again with water (very important!).
The descaling uid can be obtained from our
After-sales service or from our website.
Accessory code
(After-sales)
Name of accessory
(Online shop)
00311715 TDZ1101
7. Holding your steam generator in the lateral
position and using a jug, ll the boiler with 1/4
litre of water and replace the lter.
8. Shake the base unit for a few moments,
unscrew the lter again and empty the boiler
completely over a sink or bucket.
For best results, we recommend that this
operation is performed twice.
Important: before re-closing, make sure no
water remains in the boiler.
9. Replace and tighten up the lter.
To reset the “Calc’n’Clean” counter, switch
the steam station off twice, keeping it off for
at least 30 seconds each time.
(on → 30s off → on → 30s off → on)
Cleaning &
Maintenance
E
Attention! Risk of burns!
Always unplug the appliance from the
mains supply before carrying out any
cleaning or maintenance operation on it.
1. After ironing, pull out the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with a
damp cotton cloth.
3. If the soleplate is soiled with dirt or scale, clean
it with a damp cotton cloth.
4. If the cloth is synthetic, it may melt due to the
high temperature on the soleplate (18). Switch
off the steam and rub off any residue
immediately with a thickly folded, dry cotton
cloth.
5. Never use abrasive products or solvents. To
keep the soleplate smooth, you should avoid
hard contact with metal objects. Never use a
scouring pad, or chemicals to clean the
soleplate.
D
Fabric protection
soleplate cover
(Model dependent)
The fabric-protection soleplate cover (19*) is
used for steam-ironing delicate garments at
maximum temperature without damaging them.
Use of the soleplate cover also does away with
the need for a cloth to prevent shine on dark
materials.
It is advisable to rst iron a small section on the
inside of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place
the tip of the iron into the end of the soleplate
cover and pull the elastic strap over the lower
rear of the iron until it ts tightly. To release the
soleplate cover, pull the elastic strap and remove
the iron.
The fabric-protection soleplate cover may be
purchased from our customer service or from our
website
Accessory code
(After-sales)
Name of accessory
(online shop)
00571510 TDZ2045
E
Calc’n’Clean Advanced
Cleaning the Boiler
To extend the life of your steam generator and to
prevent any build up of scale, it is essential that
you rinse out the lter (5*) and the boiler after
several hours of use. If the water is hard,
increase the frequency.
Do not use descaling agents for rinsing out the
boiler, as they could damage it.
Automatic clean warning
Pilot light (11) will ash indicating that boiler must
be rinsed.
1. Check carefully that the appliance is cold and
unplugged for more than 2 hours, and that the
water tank (2) is empty.
2. Fix the iron to the stand by inserting the tip of
the iron into the front slot and moving the
xation lever (14) against the heel of the iron.
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the
lter opening.
5. Unscrew the lter (5*) and take it out.
6. (model dependent)
To wash the lter, you may:

Содержание

Скачать
Случайные обсуждения