![Gigabyte ga-h170m-d3h [16/44] Sata express sata express connectors](/img/pdf.png)
Gigabyte ga-h170m-d3h [16/44] Sata express sata express connectors
![Gigabyte ga-h170m-d3h [16/44] Sata express sata express connectors](/views2/1167900/page16/bg10.png)
5) SATA EXPRESS (SATA Express Connectors)
Each SATA Express connector supports a single SATA Express device.
6) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s
standard. Each SATA connector supports a single SATA device. The Intel
®
Chipset supports RAID 0, RAID 1,
RAID 5, and RAID 10. Refer to Chapter 3, "Conguring a RAID Set," for instructions on conguring a RAID
array.
Pin No. Denition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA
Conguration," for more information.
On the motherboard there are three length adjustment holes for the M.2 SSD. Select the proper hole
for the M.2 SSD to be installed and refasten the screw and nut.
7) M.2 (M.2 Socket 3 Connector)
The M.2 connector supports M.2 SATA SSDs and M.2 PCIe SSDs and support RAID conguration through the
Intel
®
Chipset. Please note that an M.2 PCIe SSD cannot be used to create a RAID set either with an M.2 SATA
SSD or a SATA hard drive and can only be used to build a RAID set with UEFI. Refer to Chapter 3, "Conguring
a RAID Set," for instructions on conguring a RAID array.
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole
for the M.2 SSD to be installed and then screw the nut rst.
Step 2:
Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it with the screw.
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
F
_0
S
S
_0F
_F
_
80 60 42
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
F
_0
S
S
_0F
_F
_
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
F
_0
S
S
_0F
_F
_
1
1
SATA3
5 4
1 0
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
F
_0
S
S
_0F
_F
_
7
7
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
F
_0
S
S
_0F
_F
_
SATA3
3 2
- 16 -
Содержание
- Ga h170m d3h ga h170m d3h ddr3 1
- Rev 1001 12me h170md3 1001r 1
- User s manual 1
- Copyright 3
- Disclaimer 3
- Identifying your motherboard revision 3
- Chapter 1 hardware installation 4
- Chapter 2 bios setup 2 4
- Chapter 3 appendix 9 4
- Ga h170m d3h motherboard layout ga h170m d3h ddr3 motherboard layout 4
- Table of contents 4
- Box contents 5
- Ga h170m d3h 5
- Ga h170m d3h motherboard 5 two sata cables 5
- Ga h170m d3h motherboard layout 5
- Motherboard driver disk 5 i o shield 5
- User s manual 5
- Box contents 6
- Ga h170m d3h ddr3 6
- Ga h170m d3h ddr3 motherboard 5 two sata cables 6
- Ga h170m d3h ddr3 motherboard layout 6
- Motherboard driver disk 5 i o shield 6
- User s manual 6
- 1 installation precautions 7
- Chapter 1 hardware installation 7
- 2 product specifications 8
- 2 productspecifications 8
- 3 installing the cpu and cpu cooler 11
- 4 installing the memory 11
- Installing the cpu 11
- 5 installing an expansion card 12
- 6 back panel connectors 12
- D sub port 12
- Dvi d port 12
- Ps 2 keyboard mouse port 12
- Usb 2 1 port 12
- Center subwoofer speaker out orange 13
- Hdmi port 13
- Line in blue 13
- Line out green 13
- Mic in pink 13
- Rear speaker out black 13
- Rj 45 lan port 13
- Side speaker out gray 13
- Usb 3 2 port 13
- 7 internal connectors 14
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector 15
- 4 cpu_fan sys_fan1 sys_fan2 sys_fan3 fan headers 15
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 15
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from overheating 15
- Overheating may result in damage to the cpu or the system may hang 15
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 15
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 15
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 15
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 15
- Chipset please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive and can only be used to build a raid set with uefi refer to chapter 3 configuring a raid set for instructions on configuring a raid array 16
- Chipset supports raid 0 raid 1 raid 5 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array 16
- Each sata express connector supports a single sata express device 16
- Follow the steps below to correctly install an m ssd in the m connector step 1 use a screw driver to unfasten the screw and nut from the motherboard locate the proper mounting hole for the m ssd to be installed and then screw the nut first step 2 slide the m ssd into the connector at an angle step 3 press the m ssd down and then secure it with the screw 16
- M m socket 3 connector 16
- On the motherboard there are three length adjustment holes for the m ssd select the proper hole for the m ssd to be installed and refasten the screw and nut 16
- Pin no definition 16
- Sata express sata express connectors 16
- Sata3 0 1 2 3 4 5 sata 6gb s connectors 16
- The m connector supports m sata ssds and m pcie ssds and support raid configuration through the inte 16
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte 16
- To enable hot plugging for the sata ports refer to chapter 2 bios setup peripherals sata configuration for more information 16
- Ahci mode 17
- Raid mode 17
- Sure to refer to the supported configurations in the tables below according to the operating mode of your sata controller ahci mode or raid mode 17
- When installing different types of m ssds including sata ssds pcie x4 ssds and pcie x2 ssds be 17
- Acz_det 9 line2_l 18
- Ci chassis intrusion header gray connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor 18
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables 18
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5 18
- F_audio front panel audio header 18
- F_panel front panel header 18
- For hd front panel audio for ac 97 front panel audio 18
- Gnd 7 faudio_jd 18
- Gnd 7 nc 18
- Hd hard drive activity led blue connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data 18
- Line out r 10 nc 18
- Line2_r 10 sense 18
- Mic 6 nc 18
- Mic power 8 no pin 18
- Mic2_l 6 sense 18
- Mic2_r 8 no pin 18
- Nc 9 line out l 18
- Nc orange no connection 18
- Of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 18
- Pin no definition pin no definition 18
- Pled pwr_led power led yellow purple 18
- Pw power switch red connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup power management for more information 18
- Res reset switch green connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart 18
- S3 s4 s5 off 18
- Speak speaker orange connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup 18
- System status led 18
- The front panel audio header supports hd audio by default audio signals will be present on both of the front and back panel audio connections simultaneously some chassis provide a front panel audio module that has separated connectors on each wire instead 18
- The front panel audio header supports intel high definition audio hd and ac 97 audio you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 18
- The front panel design may differ by chassis a front panel module mainly consists of power switch reset switch power led hard drive activity led speaker and etc when connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly 18
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord 19
- F_usb1 f_usb2 usb 2 1 headers 19
- F_usb30_1 f_usb30_2 usb 3 2 headers 19
- From the power outlet to prevent damage to the usb bracket 19
- Spdif_o s pdif out header 19
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 19
- The headers conform to usb 3 2 specification and each header can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 2 ports please contact the local dealer 19
- This header supports digital s pdif out and connects a s pdif digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards for example some graphics cards may require you to use a s pdif digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an hdmi display to the graphics card and have digital audio output from the hdmi display at the same time for information about connecting the s pdif digital audio cable carefully read the manual for your expansion card 19
- Com serial port header 20
- Lpt parallel port header 20
- The com header can provide one serial port via an optional com port cable for purchasing the optional com port cable please contact the local dealer 20
- The lpt header can provide one parallel port via an optional lpt port cable for purchasing the optional lpt port cable please contact the local dealer 20
- Tpm trusted platform module header 20
- You may connect a tpm trusted platform module to this header 20
- Add in card 21
- Add in card connector 21
- After system restart go to bios setup to load factory defaults select load optimized defaults or 21
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one danger of explosion if the battery is replaced with 21
- Always turn off your computer and unplug the power cord from the power outlet before clearing 21
- An incorrect model 21
- Bat battery 21
- Clr_cmos clear cmos jumper 21
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself 21
- Manually configure the bios settings refer to chapter 2 bios setup for bios configurations 21
- N_ s4_s5 21
- N_ slp_s3 21
- Object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 21
- Open normal 21
- Or uncertain about the battery model 21
- Pin no definition 21
- Replace the battery 4 plug in the power cord and restart your computer 21
- Short clear cmos values 21
- Supports a thunderbol 21
- Thb_c thunderbol 21
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 21
- The battery the positive side should face up 21
- The cmos values 21
- This connector is for a gigabyte thunderbol 21
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds 21
- Used batteries must be handled in accordance with local environmental regulations 21
- When installing the battery note the orientation of the positive side and the negative side of 21
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one minute or use a metal 21
- 1 startup screen 22
- Chapter 2 bios setup 22
- 2 m i t 23
- C3 state support 24
- C6 c7 state support 24
- C8 state support 24
- Core current limit amps 24
- Cpu enhanced halt c1e 24
- Hyper threading technology 24
- Intel r turbo boost technology 24
- No of cpu cores enabled 24
- Package c state limit 24
- Power limit tdp watts power limit time 24
- Turbo rati 24
- Advanced memory settings 25
- Channel interleaving 25
- Cpu eist function 25
- Cpu thermal monitor 25
- Memory boot mode 25
- Memory enhancement settings 25
- Memory frequency mhz 25
- Memory multiplier tweaker 25
- Memory timing mode 25
- Profileddrvoltage 25
- System memory multiplier 25
- System memory multiplier memory frequency mhz 25
- Advanced power settings 26
- Advanced voltage settings 26
- Case open 26
- Channel a b memory sub timings 26
- Chipset voltage control 26
- Cpu core voltage control 26
- Cpu vcore cpu vrin dram channel a b voltage 3 v 5v 12v cpu vaxg 26
- Cpu vcore loadline calibration 26
- Dram voltage control 26
- Pc health status 26
- Rank interleaving 26
- Reset case open status 26
- Vaxg loadline calibration 26
- 1st system fan speed control sys_fan1 connector 27
- 2nd system fan speed control sys_fan2 connector 27
- Cpu fan speed control cpu_fan connector 27
- Cpu system fan fail warning 27
- Cpu system fan speed 27
- Cpu system temperature 27
- Cpu system temperature warning 27
- Fan speed percentage 27
- 3dmark01 enhancement 28
- 3rd system fan speed control sys_fan3 connector 28
- Fan speed percentage 28
- Max link speed 28
- Miscellaneous settings 28
- 3 system information 29
- Access level 29
- System date 29
- System language 29
- System time 29
- 4 bios features 30
- Boot option priorities 30
- Bootup numlock state 30
- Full screen logo show 30
- Hard drive cd dvd rom drive floppy drive network device bbs priorities 30
- Security option 30
- Csm support 31
- Fast boot 31
- Lan pxe boot option rom 31
- Network stack driver support 31
- Next boot after ac power loss 31
- Ps2 devices support 31
- Sata support 31
- Usb support 31
- Vga support 31
- Windows 8 10 features 31
- Administrator password 32
- Ipv4 pxe support 32
- Ipv6 pxe support 32
- Network stack 32
- Other pci device rom priority 32
- Storage boot option control 32
- User password 32
- 5 peripherals 33
- Audio led 33
- Initial display output 33
- Intel platform trust technology ptt 33
- Legacy usb support 33
- Offboardsatacontrollerconfiguration 33
- Usb mass storage driver support 33
- Usb storage devices 33
- Xhci hand off 33
- Aggressive lpm support 34
- Device select 34
- External sata 34
- External tpm2 34
- Hot plug 34
- Intel r bios guard technology 34
- Intel r ethernet network connection 34
- Nvmeconfiguration 34
- Parallel port 34
- Pending operation 34
- Port 0 1 2 3 4 5 34
- Sata controller s 34
- Sata mode selection 34
- Sataconfiguration 34
- Security device support 34
- Serial port 1 34
- Superioconfiguration 34
- Tpm 20 interfacetype 34
- Trusted computing 2 34
- 6 chipset 35
- Audio controller 35
- Audio dsp 35
- Dvmt pre allocated 35
- Dvmt total gfx mem 35
- High precision timer 35
- Internal graphics 35
- Pch lan controller 35
- Wake on lan 35
- 7 power management 36
- Ac back 36
- Power on by keyboard 36
- Power on by mouse 36
- Power on password 36
- Dmi link aspm control 37
- Pch aspm 37
- Peg aspm 37
- Platform power management 37
- Power loading 37
- Rc6 render standby 37
- Resume by alarm 37
- Soft off by pwr bttn 37
- 8 save exit 38
- Boot override 38
- Exit without saving 38
- Load optimized defaults 38
- Loadprofiles 38
- Save exit setup 38
- Saveprofiles 38
- 1 configuring a raid set 39
- 1 configuringaraidset 39
- A installing sata hard drive s in your computer 39
- B configuringsatacontrollermodeinbiossetup 39
- Before you begin please prepare the following items 39
- C 1 uefiraidconfiguration 39
- Chapter 3 appendix 39
- Configuringtheonboardsatacontroller 39
- Raid levels 39
- C 2 configuringlegacyraidrom 40
- Installing the operating system 40
- Installing the sata raid ahci driver and operating system 40
- 2 drivers installation 41
- Our commitment to preserving the environment 42
- Regulatory notices 42
- Regulatory statements 42
- Restriction of hazardous substances rohs directive statement 42
- Waste electrical electronic equipment weee directive statement 42
- Weee symbol statement 42
- Canada industry canada ic notices canada avis d industry canada ic 43
- Fcc notice u s a only 43
- Contact us 44
- Gigabyte esupport 44
- To submit a technical or non technical sales marketing question please link to http esupport gigabyte com 44
Похожие устройства
- Gigabyte ga-z170xp-sli Инструкция по эксплуатации
- Gigabyte ga-n3050n-d2p Инструкция по эксплуатации
- Gigabyte ga-n3050n-d3h Инструкция по эксплуатации
- Gigabyte gsmart classic grey Инструкция по эксплуатации
- Gigabyte ga-n3150m-d3p Инструкция по эксплуатации
- Gigabyte ga-n3150n-d2h Инструкция по эксплуатации
- Gigabyte ga-n3150n-d3v Инструкция по эксплуатации
- Gigabyte ga-z170-hd3p Инструкция по эксплуатации
- Gigabyte ga-b150m-d2v Инструкция по эксплуатации
- Gigabyte ga-h110m-s2hp Инструкция по эксплуатации
- Gigabyte ga-h110m-s2 Инструкция по эксплуатации
- Gigabyte brix gb-bace-3000 Инструкция по эксплуатации
- Gigabyte ga-h110m-s2h Инструкция по эксплуатации
- Gigabyte ga-z170-gaming k3. v1. Инструкция по эксплуатации
- Gigabyte ga-x99-gaming 5p Инструкция по эксплуатации
- Gigabyte ga-x99p-sli Инструкция по эксплуатации
- Gigabyte ga-h170-gaming 3 Инструкция по эксплуатации
- Gigabyte ga-h170-d3h Инструкция по эксплуатации
- Gigabyte ga-h170-hd3 Инструкция по эксплуатации
- Gigabyte ga-b150n phoenix-wifi Инструкция по эксплуатации