![Makita 4326 [10/32] Rip fence optional accessory](/img/pdf.png)
Makita 4326 [10/32] Rip fence optional accessory
10
• Do not touch the blade or the workpiece immediately
after operation; they may be extremely hot and could
burn your skin.
• Always secure the blade firmly. Insufficient tightening of
the blade may cause blade breakage or serious per-
sonal injury.
• Use only B type blades. Using blades other than B type
blades causes insufficient tightening of the blade,
resulting in a serious personal injury.
To install the blade, loosen the bolt counterclockwise on
the blade holder with the hex wrench.
With the blade teeth facing forward, insert the blade into
the blade holder as far as it will go. Make sure that the
back edge of the blade fits into the roller. Then tighten the
bolt clockwise to secure the blade.
To remove the blade, follow the installation procedure in
reverse.
NOTE:
• Occasionally lubricate the roller.
Hex wrench storage (Fig. 6)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
Adjusting roller (For models 4326/4327) (Fig. 7)
Loosen the bolt on the back of the tool base with the hex
wrench. Move the retainer so that the roller contacts the
blade lightly. Then tighten the bolt to secure the tool base
and the retainer.
NOTE:
• Occasionally lubricate the roller.
Dust cover (Fig.8)
CAUTION:
• Always wear safety goggles even when operating the
tool with the dust cover lowered.
Lower the dust cover to prevent chips from flying. How-
ever, when making bevel cuts, raise it all the way.
OPERATION
CAUTION:
• Always hold the base flush with the workpiece. Failure
to do so may cause blade breakage, resulting in a seri-
ous injury.
• Advance the tool very slowly when cutting curves or
scrolling. Forcing the tool may cause a slanted cutting
surface and blade breakage.
Turn the tool on without the blade making any contact
and wait until the blade attains full speed. Then rest the
tool base flat on the workpiece and gently move the tool
forward along the previously marked cutting line. (Fig. 9)
Bevel cutting
CAUTION:
• Always be sure that the tool is switched off and
unplugged before tilting the tool base.
• Raise the dust cover all the way before making bevel
cuts.
With the base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right). (Fig. 10)
Loosen the bolt on the back of the base with the hex
wrench. Move the tool base so that the bolt is positioned
in the center of the cross-shaped slot in the base.
(Fig. 11)
Tilt the base until the desired bevel angle is obtained.
The edge of the motor housing indicates the bevel angle
by graduations. Then tighten the bolt to secure the base.
(Fig. 12)
Front flush cuts (Fig. 13)
Loosen the bolt on the back of the tool base with the hex
wrench, and slide the base all the way back. Then tighten
the bolt to secure the tool base.
Cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole
For internal cutouts without a lead-in cut from an
edge, pre-drill a starting hole 12 mm or more in diam-
eter. Insert the blade into this hole to start your cut.
(Fig. 14)
B) Plunge cutting
You need not bore a starting hole or make a lead-in
cut if you carefully do as follows.
1. Tilt the tool up on the front edge of the base with
the blade point positioned just above the work-
piece surface. (Fig. 15)
2. Apply pressure to the tool so that the front edge of
the base will not move when you switch on the tool
and gently lower the back end of the tool slowly.
3. As the blade pierces the workpiece, slowly lower
the base of the tool down onto the workpiece sur-
face.
4. Complete the cut in the normal manner.
Finishing edges (Fig. 16)
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear.
The underside of the workpiece can be greased instead
of using a coolant.
Dust extraction (Fig.17)
Clean cutting operations can be performed by connecting
this tool to a Makita vacuum cleaner. Insert the hose of
the vacuum cleaner into the hole at the rear of the tool.
Lower the dust cover before operation.
NOTE:
• Dust extraction cannot be performed when making
bevel cuts.
Rip fence (optional accessory)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing accessories.
1) Straight cuts (Fig. 18, 19, 20 & 21)
When repeatedly cutting widths of 160 mm or less,
use of the rip fence will assure fast, clean, straight
cuts.
To install, insert the rip fence into the rectangular hole
on the side of the tool base with the fence guide fac-
ing down. Slide the rip fence to the desired cutting
width position, then tighten the bolt to secure it.
Содержание
- Символы p.6
- Symbole p.6
- Symbols p.6
- English p.7
- Specification p.7
- Explanation of general view p.7
- Save all warnings and instructions for future reference p.7
- General power tool safety warnings p.7
- Use clamps or another practical way to secure and support the workpiece to a stable platform p.8
- Specific safety rules p.8
- Do not let comfort or familiarity with product gained from repeated use replace strict adher ence to jig saw safety rules if you use this tool unsafely or incorrectly you can suffer serious personal injury 1 hold power tools by insulated gripping sur faces when performing an operation where the cutting tool may contact hidden wiring or its own cord p.8
- Always use safety glasses or goggles ordi nary eye or sun glasses are not safety glasses 4 avoid cutting nails inspect workpiece for any nails and remove them before operation 5 do not cut oversize workpiece 6 check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor workbench etc 7 hold the tool firmly 8 make sure the blade is not contacting the workpiece before the switch is turned on 9 keep hands away from moving parts 10 do not leave the tool running operate the tool only when hand held 11 always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece 12 do not touch the blade or the workpiece immediately after operation they may be extremely hot and could burn your skin 13 do not operate the tool at no load unneces sarily p.8
- Functional description p.9
- Speed adjusting dial for models 4327 4328 4329 fig 3 p.9
- Installing or removing saw blade fig 4 5 p.9
- Warning misuse or failure to follow the safety rules stated in this instruction manual may cause serious personal injury p.9
- Switch action fig 2 p.9
- Some material contains chemicals which may be toxic take caution to prevent dust inhala tion and skin contact follow material sup plier safety data 15 always use the correct dust mask respirator for the material and application you are work ing with p.9
- Selecting the cutting action for models 4328 4329 fig 1 p.9
- Save these instructions p.9
- Assembly p.9
- Straight cuts fig 18 19 20 21 p.10
- Rip fence optional accessory p.10
- Operation p.10
- Metal cutting p.10
- Hex wrench storage fig 6 p.10
- Front flush cuts fig 13 p.10
- Finishing edges fig 16 p.10
- Dust extraction fig 17 p.10
- Dust cover fig 8 p.10
- Cutouts p.10
- Bevel cutting p.10
- Adjusting roller for models 4326 4327 fig 7 p.10
- Cover plate for aluminum base optional accessory fig 28 p.11
- Anti splintering device for steel base optional accessory fig 26 p.11
- Anti splintering device for aluminum base optional accessory fig 27 p.11
- Accessories p.11
- Maintenance p.11
- For european countries only p.11
- Circular cuts fig 22 23 24 25 p.11
- 4328 4329 p.12
- Ec declaration of conformity p.12
- Ce 2007 p.12
- Deutsch p.13
- Übersicht p.13
- Technische daten p.13
- Bewahren sie alle warnungen und anweisungen für spätere bezugnahme auf p.13
- Allgemeine sicherheitswarnungen für elektrowerkzeuge p.13
- Wahl der schnittbewegung für modelle 4328 4329 abb 1 p.15
- Spezielle sicherheitsregeln p.15
- Funktionsbeschreibung p.15
- Bewahren sie diese hinweise sorgfältig auf p.15
- Schutzhaube abb 8 p.16
- Schalterfunktion abb 2 p.16
- Montage demontage des sägeblatts abb 4 u 5 p.16
- Montage p.16
- Inbusschlüssel aufbewahrung abb 6 p.16
- Hubzahl stellrad für modelle 4327 4328 4329 abb 3 p.16
- Gehrungsschnitte p.16
- Einstellen der führungsrolle für modelle 4326 4327 abb 7 p.16
- Betrieb p.16
- Splitterschutz für aluminium grundplatte sonderzubehör abb 27 p.17
- Schneiden von metall p.17
- Randnahe schnitte abb 13 p.17
- Parallelanschlag sonderzubehör p.17
- Bearbeitung von kanten abb 16 p.17
- Ausschnitte p.17
- Abdeckplatte für aluminium grundplatte sonderzubehör abb 28 p.17
- Staubabsaugung abb 17 p.17
- Splitterschutz für stahl grundplatte sonderzubehör abb 26 p.17
- Zubehör p.18
- Wartung p.18
- Nur für europäische länder p.18
- Ce konformitätserklärung p.18
- Ce 2007 p.18
- Zachowaj wszystkie ostrzeżenia i instrukcje do wykorzystania w przyszłości p.19
- Wyjaśnienia dotyczące urządzenia i jego użycia p.19
- Polski p.19
- Ogólne ostrzeżenia dotyczące bezpieczeństwa dla urządzenia zasilanego prądem p.19
- Dane techniczne p.19
- Wybór sposobu cięcia dla modeli 4328 4329 rys 1 p.21
- Szczegółowe zasady bezpieczeństwa p.21
- Opis działania p.21
- Działanie włącznika rys 2 p.21
- Zawsze używaj maski przeciwpyłowej respiratora właściwego dla obrabianego materiału i wykonywanej pracy p.21
- Zachowaj tę instrukcję p.21
- Cięcie ukośne p.22
- Zakładanie lub wyjmowanie brzeszczotu rys 4 i 5 p.22
- Składanie p.22
- Regulacja wałka dla modeli 4326 4327 rys 7 p.22
- Przechowywanie klucza sześciokątnego rys 6 p.22
- Postępowanie p.22
- Pokrętło regulacji prędkości dla modeli 4327 4328 4329 rys 3 p.22
- Pokrywa przeciwpyłowa rys 8 p.22
- Wyciąganie pyłu rys 17 p.23
- Urządzenie antyodpryskowe dla stalowej podstawy wyposażenie dodatkowe rys 26 p.23
- Urządzenie antyodpryskowe dla aluminiowej podstawy wyposażenie dodatkowe rys 27 p.23
- Płyta ochronna dla aluminiowej podstawy wyposażenie dodatkowe rys 28 p.23
- Prowadnica wyposażenie dodatkowe p.23
- Cięcie metalu p.23
- Wykańczanie brzegów rys 6 p.23
- Wycięcia p.23
- Wyposażenie p.24
- Ue deklaracja zgodności p.24
- Tylko dla krajów europejskich p.24
- Szummy p.24
- Model 4328 4329 p.24
- Model 4326 4327 p.24
- Konserwacja p.24
- Drgania p.24
- Ce 2007 p.24
- Русский язык p.25
- Инструмент должен быть подсоединен только к источнику питания с напряжением указанным в табличке номиналов и может функционировать только от однофазного источника питания переменного тока в соответствии с европейским стандартом имеется двойная изоляция следовательно возможно использование с розетками без провода заземления p.25
- Технические характеристики p.25
- Сохраните все предупреждения и инструкции для дальнейшего использования p.25
- Общие предупреждения относительно безопасности электрического инструмента p.25
- Особые правила безопасности p.27
- Сохраните эти инструкции p.27
- Выбор режима резки для моделей 4328 4329 рис 1 p.28
- Установка или удаление лезвия пилы рис 4 и 5 p.28
- Сборка p.28
- Регулятор переключения скорости для моделей 4327 4328 4329 рис 3 p.28
- Действия при переключении рис 2 p.28
- Описание функционирования p.28
- Хранение торцевого гаечного ключа рис 6 p.29
- Резка металла p.29
- Регулирующий ролик для моделей 4326 4327 рис 7 p.29
- Пылезащитный чехол рис 8 p.29
- Передние разрезы вровень рис 13 p.29
- Отделка краев рис 16 p.29
- Наклонная резка p.29
- Вырезание p.29
- Эксплуатация p.29
- Ехническое обслуживание p.30
- Удаление пыли рис 17 p.30
- Стыковочная накладка для алюминиевого основания дополнительная принадлежность рис 28 p.30
- Противорасщепляющее устройство для стального основания дополнительная принадлежность рис 26 p.30
- Противорасщепляющее устройство для алюминиевого основания дополнительная принадлежность рис 27 p.30
- Принадлежности p.30
- Направляющая планка дополнительная принадлежность p.30
- Ce 2007 p.31
- Ес декларация соответствия p.31
Похожие устройства
-
Makita 4329Инструкция по применению -
Makita 4328Инструкция по применению
-
Makita 4327Руководство пользователя
-
Makita 4326Руководство по работе с устройством
-
Makita 4329Руководство по эксплуатации -
Makita 4326Инструкция по эксплуатации -
Makita 4327Инструкция по эксплуатации -
Makita 4329Инструкция по эксплуатации
-
Makita 4350CTИнструкция по эксплуатации -
Makita 4351CTИнструкция по эксплуатации -
Makita 4351FCTИнструкция по эксплуатации
-
Makita 4350FCT, 720 ВтИнструкция по эксплуатации