Home
Главная
Yamaha
Сетевой адаптер
ywa-10
Инструкция по эксплуатации Страница: 1

Yamaha ywa-10 Инструкция по эксплуатации онлайн

YWA-10

Wireless Network Adapter

Owner’s Manual

English

YWA-10/EN-1

Allows Yamaha AV products equipped with a

NETWORK port and a DC OUT jack to be connected

with a wireless LAN.

Compatible devices can connect to the YWA-10

through a USB connector instead of a DC OUT jack.

Refer to the website below for a list of compatible

devices.

http://yamaha.com/

The firmware of this unit may be updated at times for

improvement. Please refer to the following website for

information on firmware updates.

http://yamaha.com/

Features

AV Receiver

YWA-10

Internet

connection

Modem

Wireless LAN router

(base unit)

Setup procedure

Checking the base unit

• Check that the Wireless LAN router (base unit)

can connect to the Internet.

Connecting to the base unit

• When the Wireless LAN router (base unit) has a

WPS button

^ Carry out the procedures in “Step 2-A

Connecting to the base unit (using WPS)” to

connect to the base unit.

• When the Wireless LAN router (base unit) does

not have a WPS button

^ Carry out the procedures in “Step 2-B

Connecting to the base unit (manual

configuration)” to connect to the base unit.

✻ If connecting using “(using WPS)” does not

succeed, refer to “(manual configuration)” and

configure the connection.

Connecting to an AV product

The Wi-Fi CERTIFIED Logo is a

certification mark of the Wi-Fi

Alliance.

The Wi-Fi Protected Setup Mark

is a mark of the Wi-Fi Alliance.

a POWER indicator

b WPS indicator

c WIRELESS indicator

d Power connector

e LAN1 port, LAN2 port

f WPS button

g Reset button

• If you do not already have an Internet connection, please apply for one

before setting up this unit.

• Do not connect the USB power cable to a USB hub.

Part names

Things to check before setup

a b

d e f

Upper surface of product Rear

Side

a Check that the wireless LAN router (base unit) can connect to the

Internet without difficulty.

Notes

• If you do not currently have an Internet subscription, please obtain one.

• A wireless LAN router is required to set up a connection using this

procedure. Please obtain a wireless LAN router if you do not have one

available.

b Check whether the wireless LAN router (base unit) is WPS compatible.

Check the owner's manual and other documentation supplied with the

wireless LAN router.

Note

WPS (Wi-Fi Protected Setup) is a function that uses a button to configure

connections and security on wireless LAN devices.

*Some Wi-Fi devices have “WPS” written on them.

Step 1 Checking the base unit

W When the wireless LAN router (base unit) has a WPS button

Carry out “Step 2-A Connecting to the base unit (using WPS)”, and then

“Step 3 Connecting to an AV product”, in that order.

W When the wireless LAN router (base unit) does not have a WPS

button

Carry out “Step 2-B Connecting to the base unit (manual configuration)”,

and then “Step 3 Connecting to an AV product”, in that order.

Computer

Internet connectivity

Wireless LAN

router

(base unit)

Modem

Internet

connection

Notes

• This explanation details the procedure for connecting using the WPS

function. When using a base unit that is not equipped with a WPS

function, refer to “Step 2-B Connecting to the base unit (manual

configuration)” at right.

• You will need to change the IP address of this unit if you are using more

than one YWA-10 at the same time.

Refer to “Troubleshooting” on the reverse page for more details.

1. Supply power to the YWA-10

a Turn on the power of the AV product that you wish to connect this unit

to.

b Use the supplied USB power cable to connect the power connector on

this unit to the DC OUT jack on the AV product.

The indicator on the front panel of this unit lights. Wait for approximately one

minute after the indicator lights and then carry out the following procedure.

Note

If the AV product is not equipped with a DC OUT jack, connect to the USB

connector on the front panel.

2. Connect the base unit

a Press the WPS button on the wireless LAN router (base unit).

Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to use the WPS button.

b Press and hold the WPS button on the rear of this unit for more than 5

seconds and release it.

The WPS indicator on the front panel lights.

c Wait until the WPS indicator turns off (this will take two minutes at

most).

Note

If the WPS indicator blinks, carry out procedure 2 again, starting at number

Step 2-A

Connecting to the base unit

(using WPS)

This completes connection with the base unit. Proceed to “Step 3

Connecting to an AV product”.

AV Receiver

Rear Panel

Press and hold for more

than 5 seconds.

Notes

• When making a manual connection to the base unit, or when you are

unable to connect using the procedure described in “Step 2-A Connecting

to the base unit (using WPS)” at left, refer to the explanation below.

• If the PC you are using to configure this unit is connected to the wireless

LAN, turn the PC’s wireless LAN function off.

• You will need to change the IP address of this unit if you are using more

than one YWA-10 at the same time.

Refer to “Troubleshooting” on the reverse page for more details.

1. Check the network that you are attempting to

connect to.

You will need the setting information from the wireless LAN router (base unit)

when connecting or setting up this unit. Have the following table ready for use.

* Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to check its wireless LAN settings.

■ When using WEP security settings

*1: 16-digit number (0–9, A–F), *2: ASCII (0–9, A–Z, a–z)

■ When using WPA/WPA2 security settings

Note

Use only alpha-numeric characters (0–9, A–Z, a–z) for an SSID or password.

Otherwise, Yamaha cannot guarantee normal operation.

Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to change the SSID or password.

2. Connect this unit to a PC

a Turn the PC power on.

b Use the supplied LAN cable to connect the LAN1 port (or the LAN2 port)

on this unit to the LAN port on the PC. Then, use the supplied USB

power cable to connect the power connector on this unit to the USB

connector on the PC.

The indicator on the front panel of this unit lights. Wait for approximately one

minute after the indicator lights and then carry out the following procedure.

3. Setting up this unit

a Start the web browser on the PC.

b Enter “ywa.setup” in the

address field in the Web

browser, and press the Enter

key.

Note

If the login screen does not appear even after you enter “ywa.setup”, enter

“192.168.1.249” and press the Enter key. If the login screen still does not

appear, refer to “Troubleshooting”.

Step 2-B

Connecting to the base unit

(manual configuration)

Name Wireless LAN setting

(1) SSID

(2) Security mode ❑ Open ❑ Shared

(3) Security key type

❑ Hexadecimal

❑ ASCII

(4) Default key ❑ Key 1 ❑ Key 2 ❑ Key 3 ❑ Key 4

(5) Password

Name Wireless LAN setting

(1) SSID

(2) Security mode ❑ WPA-PSK ❑ WPA2-PSK

(3) Encryption type ❑ TKIP ❑ AES

(4) Password

To assure the finest performance, please read this

manual carefully.

Keep it in a safe place for future reference.

Check that the following accessories are supplied with

the product.

Owner’s Manual (this manual)

Package contents

Wireless Network

Adapter (this unit)

LAN cable

USB power cable

Continues to the back side.

YWA-10_dtp_En.fm Page 1 Thursday, April 12, 2012 12:07 AM

Yamaha ywa-10 Инструкция по эксплуатации онлайн

Содержание

Похожие устройства