![Graco Dispensit 1093 [3/24] Warning](/img/pdf.png)
Graco Dispensit 1093 [3/24] Warning
![Graco Dispensit 1093 [3/24] Warning](/views2/1193568/page3/bg3.png)
Warnings
332089B 3
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the dispense outlet.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning,
checking, or servicing equipment.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
• Always wear impervious gloves when spraying or cleaning equipment.
• If this equipment is used with isocyanate material, see additional information on isocyanates in Iso-
cyanate Conditions Section of this manual.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
Содержание
- Dispensit 1092 1
- Operation maintenance 1
- Patented meter and dispense system for precise one component micro dispensing not for use in explosive atmospheres 1
- Contents 2
- Warning 3
- Warnings 3
- Warning 4
- Changing materials 5
- Isocyanate conditions 5
- Material self ignition 5
- Moisture sensitivity of isocyanates 5
- Grounding 6
- Overview 6
- Optional cycle detection sensors 7
- Suggested sequence of operation see page 16 7
- Component identification 8
- Controls 8
- Liquid control 8
- System shown with optional 4104a controls 8
- Top view of controls 8
- Typical system configurations 8
- Typical feed system components 9
- Typical feed system components continued 10
- Metering valve 11
- Typical installation 12
- As desired use the following diagram to mount the metering valve 13
- Valve mounting diagram 13
- Startup 14
- Adjusting the shot size 15
- Operation 16
- Sequence of operation 16
- Step 1 reload 16
- Step 2 shift 16
- Step 3 dispense 16
- Air dryer 17
- Maintenance 17
- Material reservoirs 17
- Metering rod port 17
- Pressure relief procedure 17
- Shutdown 17
- Spool valve port 17
- Schematics 18
- Troubleshooting 18
- Cutaway front view 19
- Cycle the valve a few times to remove residual material pressure 19
- Disassembly 19
- For models with cycle detection sensors discon nect the electrical power from the cycle detection sensors note the position of the sensors then remove them by loosening the set screws and slid ing them out carefully 19
- For part references in the following proce dure 19
- Material inlet port on side of block 19
- Material outlet needle not shown 19
- Rebuild 19
- Refer to 19
- Remove the air pressure lines from the air supply tee fittings 17 17 do not remove the fittings themselves 19
- Remove the dispense valve from its mounting 19
- Remove the material inlet line from the inlet block 19
- Turn off the air pressure to the 1092 19
- Turn off the material inlet pressure to the 1092 19
- Assembly 20
- Electrical requirements cycle detection option 22
- Technical data 23
- For the latest information about graco products visit www graco com 24
- Graco headquarters minneapolis international offices belgium china japan korea 24
- Graco inc and subsidiaries p o box 1441 minneapolis mn 55440 1441 usa copyright 2010 graco ohio inc all graco manufacturing locations are registered to iso 9001 www graco com revised january 2015 24
- Graco information 24
- Graco standard warranty 24
- To place an order contact your graco distributor or call to identify the nearest distributor toll free 1 800 746 1334 or fax 330 966 3006 24
Похожие устройства
- Graco Dispensit 1093 Технические характеристики
- Graco MD2 Инструкция по эксплуатации
- Graco MD2 Технические характеристики
- Graco 256994 Инструкция по эксплуатации
- Graco 256994 Технические характеристики
- Graco 256290 Инструкция по эксплуатации
- Graco 256290 Технические характеристики
- Graco 15V813 Инструкция по эксплуатации
- Graco 15V813 Технические характеристики
- Graco 256292 Инструкция по эксплуатации
- Graco 256292 Технические характеристики
- Graco 256293 Инструкция по эксплуатации
- Graco 256293 Технический паспорт
- Graco 15V814 Инструкция по эксплуатации
- Graco 15V814 Технические характеристики
- Graco 256295 Инструкция по эксплуатации
- Graco 256295 Технические характеристики
- Graco 256296 Инструкция по эксплуатации
- Graco 256296 Технические характеристики
- Graco 256297 Инструкция по эксплуатации