Pioneer CDJ-400 Инструкция по эксплуатации онлайн [13/162] 18521
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Pioneer CDJ-400 Инструкция по эксплуатации онлайн [13/162] 18521

Pioneer CDJ-400 Инструкция по эксплуатации онлайн [13/162] 18521
OPERATIONS (DISC LOADING/UNLOADING)
13
<DRB1451>
En
English
DISC LOADING/UNLOADING
Label surface up
Insert straight
1. Set the rear-panel POWER switch to ON.
Do not force a disc into the unit when the POWER switch
is set to OFF as this may damage the disc and the unit.
2. Insert a disc.
÷ Hold the disc with label surface upwards, and insert into
the front panel disc loading slot.
÷ Only one disc can be loaded at a time. Never attempt to
load more than one disc at the same time, or attempt to
load a second disc when one disc has already been
loaded.
÷ When loading a disc, do not placing any twisting force
on the disc, or try to force the disc into the slot. Also, do
not attempt to interrupt or defeat the motion of the disc
when the player begins to draw a disc into the slot or to
eject a disc, since damage to the disc or player could
occur.
3. Press the EJECT button to remove the disc.
÷ When the EJECT button is pressed, disc rotation stops
and the disc is ejected from the loading slot.
÷ If the disc cannot be ejected with the EJECT button, in-
sert a pin in the forced ejection hole on the front panel of
the player.
7 Canceling eject command
In the event the EJECT button is pressed by mistake, if the
PLAY/PAUSE (6) button is pressed immediately (before
[EJECT] is displayed), the eject command will be canceled
and playback will restart from the place immediately
before the EJECT button was pressed (during this time,
sound output will be temporarily interrupted).
CAUTION:
Do not attempt to press a disc back into the slot when
the [EJECT] indicator appears. Pressing a disc back into
the slot while the [EJECT] indicator appears may cause
the player to stop. In this case, press the EJECT button
again and wait until the [EJECT] indicator goes out be-
fore reinserting the disc.
Forced disc ejection
If the EJECT button does not function or the disc cannot
be removed, pushing the pin provided into the forced
ejection hole on the front panel will enable the disc to be
removed.
When performing forced ejection, be sure to follow the
precautions below.
1 Be sure to turn OFF the power of the CD player, and
check that the disc has stopped rotating. It takes
about 60 seconds for the disc to stop rotating after the
power has been turned OFF.
If forced ejection is performed while the disc is rotating;
÷ As the disc will be ejected outside the CD player rotat-
ing, it may hit your finger and cause injuries.
÷ As the disc will be rotating with the clamp unstable, it
may be scratched.
For the above reasons, never attempt to eject the disc
forcibly while it is rotating.
2 Always use the pin provided (Do not use other objects).
The provided pin is found in a groove in the bottom sur-
face of the player.
When the provided forced eject pin is inserted fully into
the forced eject hole on the front panel, the loaded disc
is ejected about 5 mm to 10 mm from the loading slot,
making it possible to remove it by hand.
Forced ejection hole

Похожие устройства

OPERATIONS DISC LOADING UNLOADING 3 Press the EJECT button to remove the disc When the EJECT button is pressed disc rotation stops and the disc is ejected from the loading slot If the disc cannot be ejected with the EJECT button in sert a pin in the forced ejection hole on the front panel of the player Canceling eject command In the event the PLAY PAUSE EJECT and is the button button displayed playback before EJECT ll will the button pressed pressed eject restart EJECT is is command from was by mistake immediately the pressed will be if the before canceled place immediately during this time sound output will be temporarily interrupted CAUTION Do not attempt to press a disc back into the slot when the EJECT indicator appears Pressing a disc back into the slot while the EJECT indicator appears may cause the player to stop In this case press the EJECT button again and wait until the EJECT indicator goes out be fore reinserting the disc 1 Set the rear panel POWER switch to ON Do not force a disc into the unit when the POWER switch is set to OFF as this may damage the disc and the unit 2 Insert a disc Hold the disc with label surface upwards and insert into the front panel disc loading slot Only one load disc more load a can than be one second loaded disc disc at at a the when time Never to attempt to time disc has already been placing any twisting force one or attempt same loaded When loading a disc do not on the disc or try to force the disc into the slot Also do not attempt to interrupt or defeat the motion of the disc when the player begins to draw a disc into the slot or to eject a disc since damage to the disc or player could occur Forced disc ejection If the EJECT button does not function or the disc cannot into the forced Always use the pin provided Do not use other objects ejection hole on the front panel will enable the disc to be The provided pin is found in a groove in the bottom sur face of the player removed When be removed When pushing performing the forced pin ejection provided be sure to follow the the the provided forced forced eject hole ejected about 5 on precautions below is making it possible to remove it by hand that the disc has stopped rotating It to pin front Be sure to turn OFF the power of the CD player and check mm eject the 10 mm is inserted fully into panel the loaded disc from the loading slot takes about 60 seconds for the disc to stop rotating after the power has been turned OFF If forced ejection is performed while the disc is rotating As the disc will be ejected outside the CD player rotat As ing it may hit your finger and cause injuries the disc will be rotating with the clamp unstable it may be scratched For the above reasons never attempt to eject the disc forcibly while it is rotating 13 DRB1451 En English DISC LOADING UNLOADING

Скачать